Kromrey Disclosure - Bedini SG - Beyond the Advanced Handbook by Peter Lindemann

[brodonh]

Hi All,
My 15yr old Gabie and I just hooked the rig to 8 golf cart batts.
She's running at 12v in and 1200rpm at about 3A.
Those GC batts are charging very well.
After she warmed up it was easy to move into single pulse triggering.
Very encouraging!
bro d

[brodonh]

last two for now.

RS found some problems with the schematics so I've corrected them.

I built off the board diagrams for my working unit.

bro d

[brodonh]

1 more set after this

[brodonh]

I've deleted the circuit boards that I've made and previously posted.
I'll post the circuits with the boards so one can see both.
These circuits and boards are for the battery rotation system.
It has consistently worked without a problem.
bro d

2 of 6 ccts and boards

[brodonh]

I've deleted the circuit boards that I've made and previously posted.
I'll post the circuits with the boards so one can see both.
These circuits and boards are for the battery rotation system.
It has consistently worked without a problem.
bro d

[brodonh]

Hi All,
When running with everything matched the rotation system was flawless, as usual.
One of the banks was close to 22v after all starting at full charge.
Run time about 60hrs.
Amp draw about 2.25A.

I unhooked the generator windings from the charge batt (while running) and instantly blew 2 matched transistors.
That stopped the run.

The split positive system is not maintaining itself on my bench, with my best efforts so far.

I'm going to study it on a single coil bike wheel for a while.
The generator windings, in a sense protect the transistors.

Keepin' on,
bro d

[Deuis]

Authentic enough yeah. (not sure I like your accent though).

If you friend the people your following their posts come up in your profile so you dont have to look through the forum.

[brodonh]

Hi Deuis,
Didn't know about "friend request" on this forum.
I failed to show the power coil board that I'm using, so I'll attach it.
Also I'm going to change the rotation sequence to the one that Eric Nissen/Peter L used.
Have to make a different diode board for that. Can do it today.

G'day Mate, (does that sound authentic?)

bro d

[Deuis]

Hi Brodonh,

I am watching your setup, but yes participation is very low indeed.
Perhaps opening up the Blog will be an easier way to follow builders rather than being lost in threads.
Then you really can journal all of your builds in one place easily.

Hi All,
This seems like a journal rather than a thread where interested parties are are participating.
I've made a new 8 tranny run board and have matched every thing but the R's for the neon lights.
It runs for 2 or three days and then one of the 24v battery banks will get down around 20v, which is too low.
I can work with it while it is running and ease the load on that bank until it becomes the charge bank and then up the amp draw for that bank's charging.
Peter wrote about eliminating crossed wires. I would like to know more about that subject.

My battery rotate system works with no problems, If one is interested in having one, then contact me privately.


Bro d

[brodonh]

Hi All,
This seems like a journal rather than a thread where interested parties are are participating.
I've made a new 8 tranny run board and have matched every thing but the R's for the neon lights.
It runs for 2 or three days and then one of the 24v battery banks will get down around 20v, which is too low.
I can work with it while it is running and ease the load on that bank until it becomes the charge bank and then up the amp draw for that bank's charging.
Peter wrote about eliminating crossed wires. I would like to know more about that subject.

My battery rotate system works with no problems, If one is interested in having one, then contact me privately.


Bro d

[brodonh]

Hi all,
Tried split triggering with the system.
I moved the magnets on one rotor to between the mags on the other.
Planned on having alternating triggering with twice as many spikes while alternating mags between the 2 rotors.

If the battery rotate system stays in place then the tops of both run coils must remain tied together and the ground (from pos of charge batt) is common.
The trigger wires from the tops of the 2 run coils are the only wires that are separated along with the 4 collector wires from each run coil bottom.

I had two pots setup and got one running good and then hooked the 2nd.
It goes into self oscillation mode and stops spinning the rotors. More than double the amp draw of one side.
The oscillations alternate according to the 2 channel scope shot
very interesting.

Next test might be to run separate batteries for each side without the rotate system.

Also I'll try split triggering with mags aligned on both rotors.

bro d

[brodonh]

Split Pos 8 inline board

I was blowing too many transistors with other boards so made a new one.
There is a barrier block soldered in the 24 holes (all pin #1) that receives the run wires and the base resistors.

[brodonh]

Made board with DC to DC converter to isolate arduino power supply from aux battery.

Now I can charge aux battery with gen coil or gen winding making rig totally self sufficient.

bro d

Hi All,
When I switch the gen windings ( 2) to charge the Aux battery, the amp draw decreases instantly about 8% and the aux batt charges rapidly.
I'm sending the pulses through an ultrafast diode. 24v pulses into 12v battery.
Very encouraged.
bro d

[brodonh]

Made board with DC to DC converter to isolate arduino power supply from aux battery.

Now I can charge aux battery with gen coil or gen winding making rig totally self sufficient.

bro d

[brodonh]

Showed my rig to an e-tech friend who is totally open.
I was running the split+ at less than 3A, 12v and the charge battery was over charging, so I put a 50W 12v bulb on it and the battery was still charging slowly.
Also I had 60 Led's hooked up to a gen coil.

Looks like about 6A worth of work for less than 3.

Keepin' on.
bro d