Kromrey Disclosure - Bedini SG - Beyond the Advanced Handbook by Peter Lindemann

[brodonh]

Hi All,
Been at it.
Made a new run coil board and I 'm using 4 gen windings per run coil through ultrafast diode.
Reinstalled the original run coils and triggering with #20 wire.
At single pulse she wants 4-5A.
In order to get it down to less than 2A I'm having to go with quadruple pulse triggering.
After watching vid again, I'll experiment with slower ultrafast diodes. Peter said that the mur3060 was too fast for the machine and I've been using faster than that.
Waiting for parts.
God bless the vets.
bro d

[brodonh]

Tom C,
I hope that you and the family are doing well.
I have a question that I should have had answered long ago.
How many Gen windings (Not gen coils)did Peter use from each run coil.
IN the vids I see what looks like 4 pwr and another 4 that I suspect to be gen windings.
On the terminal block at the motor circuit I see 7 wires connected.
Did he have the gen windings all going through one diode per run coil?
I missed more than this in the build, but my swapper is working perfectly. PTL
Thanks for a little help with your busy schedule.
bro d

[brodonh]

I don't have a schematic for the battery rotate system.

I drew sketches of what I needed each board to do and then used Target (free) software to draw the boards.

I learned the type of relays that were used and bought a few to get aquainted with switching them.

I made the most simple board and tested it.

The arduino sketch is primitive at best compared to an advanced programmer and it is not the same micro computer that Peter had in place.

I bought an arduino shield that allows me to screw in all connections. More than 50.



bro d

[Brian McNece]

Hi Brian,
I have a number of pics. For your consideration.
It was a BIG undertaking for me.
You should watch the Peter L video that this thread is about.
bro d

[ATTACH=CONFIG]6289[/ATTACH][ATTACH=CONFIG]6290[/ATTACH][ATTACH=CONFIG]6291[/ATTACH][ATTACH=CONFIG]6288[/ATTACH]

Thank you, very nice setup.

[brodonh]

Hi Brian,
I have a number of pics. For your consideration.
It was a BIG undertaking for me.
You should watch the Peter L video that this thread is about.
bro d

[Brian McNece]

Hi All,
I've got the Swapper running again.
I'm running it on one coil with 6 pwr strands and the usual setup.
It held charge on all batts yesterday for about 12hrs and then it quit running during the night.
When I checked it this AM the the batts were all up close to 25v or higher, so so there was a switching problem with the arduino based batt rotate sys.
I restarted the arduino board a few times and then all is working again. I suspect that power went out from the mains long enough to disrupt the rotate cycle.
The arduino board is powerd by a usb cable from a computer that puts out 5v when tha PC is off.
The batts are all holding and she runs at 750rpm. I'm using only one gen coil at present. 18 total hrs so far and the batts are all up in V.

bro d

Are you willing to share the swapper circuit, and the sketch for the arduino? I have a manual swapping device but i recently got the arduino and was thinking it would be nice to do the swapping with that instead. Still learning to use the arduino.

[brodonh]

Hi All,
I changed to above mentioned coil setup and it works as desired. 1200 rpm instead of 750. about 2A draw with single pulse.
Spikes are about 210v. Batteries seem to be holding up OK. Will have pics.
bro d

[brodonh]

I'm going to change to a 20 gauge coil and run 6 pwr strands and a gen winding. The extra large cores that I have on the 1st build are amp hogs at a single pulse triggering.
I've been running with dbl pulse to keep the amps down. I hope to see a single pulse (much faster( at less than 2A).
Will have pics or link to vid, soon.
bro d

[brodonh]

Hi All,
I've got the Swapper running again.
I'm running it on one coil with 6 pwr strands and the usual setup.
It held charge on all batts yesterday for about 12hrs and then it quit running during the night.
When I checked it this AM the the batts were all up close to 25v or higher, so so there was a switching problem with the arduino based batt rotate sys.
I restarted the arduino board a few times and then all is working again. I suspect that power went out from the mains long enough to disrupt the rotate cycle.
The arduino board is powerd by a usb cable from a computer that puts out 5v when tha PC is off.
The batts are all holding and she runs at 750rpm. I'm using only one gen coil at present. 18 total hrs so far and the batts are all up in V.

bro d

[Faraday88]

As Tom mentioned, I'm putting the 2A12's back into production.

I'll post a video soon with Tom and I and we'll tell you what's coming up!

Wow!! Great will immidiately purchase one
Rgds,
Faraday88

[Aaron Murakami]

Hi Tom C,

Thanks for the update..how can i place an order for the 2A 12.. what happend to the Extreme series of the 2A 12 version..?
Rgds,
Faraday88.

As Tom mentioned, I'm putting the 2A12's back into production.

I'll post a video soon with Tom and I and we'll tell you what's coming up!

[Faraday88]

We do not know, right now we are focusing on sideband generators, retooling the bedini amp line, and we are working on some other Bedini related tech. We do have some old stock 2A12 units, they were the last completed batch from the shop. we still have cap dumps and linear regulators.

Aaron is working hard to get a charger line back up and available.

Tom C

Hi Tom C,

Thanks for the update..how can i place an order for the 2A 12.. what happend to the Extreme series of the 2A 12 version..?
Rgds,
Faraday88.

[Tom C]

We do not know, right now we are focusing on sideband generators, retooling the bedini amp line, and we are working on some other Bedini related tech. We do have some old stock 2A12 units, they were the last completed batch from the shop. we still have cap dumps and linear regulators.

Aaron is working hard to get a charger line back up and available.

Tom C

[Faraday88]

RD,

Send an email to [email protected] and we can discuss this offline. to answer your question the trigger is 20 AWG. 1 drive coil plus 5 generator coils=6 per side. the bearings are sealed roller bearings. just a standard machine bearing with rubber dust seals.

you need to divide the circuit in half by cutting the traces on the board. and isolating the triggers, or if you are really good with timing the rotors, you can run 1 trigger and drive 2 coils with 1 trigger. our machine has slotted hubs and a slotted axle so the magnets are already timed.

this can be set up as a 6 coil SG or any combination of drive and genny coils, its a very flexible kit.


I can send you a parts list and pricing after I get your email. anyone else interested please send an email to [email protected]

Tom C

Hi Tom C ,
When shall we expect TESLAGENX to sell the Charger and Rejuvenators..??
i'm eager to book few Chargers and so are some of my Friends..they were astound to here the Charger capability..
Rgds,
Faraday88.

[Tom C]

RD,

Send an email to [email protected] and we can discuss this offline. to answer your question the trigger is 20 AWG. 1 drive coil plus 5 generator coils=6 per side. the bearings are sealed roller bearings. just a standard machine bearing with rubber dust seals.

you need to divide the circuit in half by cutting the traces on the board. and isolating the triggers, or if you are really good with timing the rotors, you can run 1 trigger and drive 2 coils with 1 trigger. our machine has slotted hubs and a slotted axle so the magnets are already timed.

this can be set up as a 6 coil SG or any combination of drive and genny coils, its a very flexible kit.


I can send you a parts list and pricing after I get your email. anyone else interested please send an email to [email protected]

Tom C

Hi Tom,

I would be interested in parts if you can come up with a list and prices. I also have some more questions like you mentioned the coils were all 18 gauge, what about the trigger wire? What type of bearings were used. you mentioned 5 coils per side, I see 6 which would be the logical thing to do. I recently received my 8 transistor SG kit and what mods were done to use it between two coils? In the pictures I could see wires from each coil going to the board and now I know more about how many wires were used. This 'mini beast' looks cool and I was always wanted to build something bigger than my first SSG. I will be getting more 8 transistor kits as money comes in. I still have to start getting more 18 gauge wire since I do not have enough on hand. Thanks for the help.