Kromrey Disclosure - Bedini SG - Beyond the Advanced Handbook by Peter Lindemann

[Dwane Dibley]

and yes!! the 1984 machine (JB's not Jim watson's) is a Pulsed Motor of one scale down to the Gray Motor in a way, as POWER Pulse is fed back to the SINGLE BATTERY...
all one needs to do is figure out the TRIGGER in each case...

Rgds,
Faraday88.

Hello Faraday88,
How is the 1984 generator like the Gray Motor? One is a generator and the other is a motor!! Also, they have completely different operational modes. The original John Bedini energiser has morphed into a self contained self drive unit where the external motor has been deleted. It uses battery power as the initial energy source to supply energy to batteries for converson into useable power. The Gray motor uses a combination of high voltage pulses and atmospheric energy to drive it: and likely relied on the Townsend effect for power. In reality, his recovery process was to keep the batteries charged only to supply high voltage pulses, a bit like an automobile alternator. The petrol, so to speak was what nobody understands. It is just that Gray himself did not fully understand how the motor worked, it was someone called Marvin Cole who put it all together.

Hope this clarifies the Gray Motor a bit for you.

Regards

Dwane

[Dwane Dibley]

Hello D,
I haven't gotten around to getting the latest Peter Lindemann book, but, does he not say how the "swapper works in his latest update?

regards

Dwane

I have the video with attached pdf file now and can see why you are asking about the battery swapper! It should not be too difficult to formulate a logic sequence to alternate the batteries and also recovery periods, and, as Peter says "feather" the excess energy. I think the real test will be to map a unit to a load and make it a dedicated power source. That way, controls of energy flow could be better managed.

Regards

[Dwane Dibley]

just wondering, are there plans to make available for sale the battery swapper that Peter L shows?

Hello D,
I haven't gotten around to getting the latest Peter Lindemann book, but, does he not say how the "swapper works in his latest update?

regards

Dwane

[Scorch]

Scorch's Kromrey converter kit

Hello all.

Questions regarding disclosure-

Is John or somebody knowledgeable of Jonh's 1984 build of the Kromrey converter willing to answer specific questions including but not limited to-

-What is the wire gauge used for the rotor coils?
-What is the approximate number of turns per coil?
-Are pole pieces solid or laminate layers?
-Are ceramic (ferrite) magnets suitable?
-Is this the correct thread to start detailing a replication attempt based on the recent disclosure?

https://www.google.com/patents/US3374376

http://freeenergyresearch.blogspot.com/2013/02/notes-on-kromrey-converter-us-patent.html

Please respond.

Kindest regards;

}:>

[Tom C]

D,

yes...

Tom C

[D Rhodes]

just wondering, are there plans to make available for sale the battery swapper that Peter L shows?

[jason mcgrath]

Hi Jason,

Can you confirm that your SG runs normally - just a single primary battery and a single charge battery?

John K.

Yes it was running well before i tried to convert it.Ill have another look at it this arvo and ill put it back to generator mode and sg mode.
Thanks john

[John_Koorn]

Thanks for your reply.Yes i have got peters presentation.So the 24 volt (witch is the input)positive is connected to the top of the coil.The 12 volt (out put battery)positive is connected to the emitter (which use to be the input negative).The 2 negatives are joined together.I double checked this but i cannot get it up to speed.It goes but then it slows down and stops.The neo bulbs came on as well when it was on.

Hi Jason,

Can you confirm that your SG runs normally - just a single primary battery and a single charge battery?

John K.

[jason mcgrath]

Hi Jason,

You shouldn't need to modify the SG circuit in any way to get it running. All you need to do to is connect the 24V positive to the SG input positive, the 12V positive to the SG input negative and the 24V negative to the 12V negative.

If you don't have the pickup winding on the coil to feed the SG output back to the 12V battery, just connect the SG output to a 4th battery.

I'm assuming you purchased Peter's presentation, otherwise the above may not make sense.

John K.

Thanks for your reply.Yes i have got peters presentation.So the 24 volt (witch is the input)positive is connected to the top of the coil.The 12 volt (out put battery)positive is connected to the emitter (which use to be the input negative).The 2 negatives are joined together.I double checked this but i cannot get it up to speed.It goes but then it slows down and stops.The neo bulbs came on as well when it was on.

[John_Koorn]

Trying to covert my sg to beyond advanced mode.I have 24 volt operation, 18 awg coils 100 FT 220 ohm base resistors.I taken the emitter off the 2 negatives ( primary and secondary )put a diode in between.Primary battery is 24 volts .secondry battery is 12 volts. running 2 coils .Its starts off but then slows down and stops.Do i need to change the base resistors and what size pot do i need for 18 gauge wire?can any one help me out? cheers Jason

Hi Jason,

You shouldn't need to modify the SG circuit in any way to get it running. All you need to do to is connect the 24V positive to the SG input positive, the 12V positive to the SG input negative and the 24V negative to the 12V negative.

If you don't have the pickup winding on the coil to feed the SG output back to the 12V battery, just connect the SG output to a 4th battery.

I'm assuming you purchased Peter's presentation, otherwise the above may not make sense.

John K.

[jason mcgrath]

Trying to covert my sg to beyond advanced mode.I have 24 volt operation, 18 awg coils 100 FT 220 ohm base resistors.I taken the emitter off the 2 negatives ( primary and secondary )put a diode in between.Primary battery is 24 volts .secondry battery is 12 volts. running 2 coils .Its starts off but then slows down and stops.Do i need to change the base resistors and what size pot do i need for 18 gauge wire?can any one help me out? cheers Jason

[Faraday88]

I wish I could order and download the third book but I have no way to use it.

If one of you would print out the complete Advanced Handbook with both sides of the paper and in color, I would of course pay you.

If you want to do this, please private message me with your fair price.

Thin Q

Whatever is 'repeated'..... Further to the Advanced handbook has definitely given the clue to merge the link between the 'Generator' and the 'Energiser' aspect of this entire episode of the Bedini technology. if you study it up close i would say that the 1984 machine is rather a MOTOR alone split in its construction, while the SSG is a ENERGIZER alone Combined in its construction, now, you give the other what the first lacks and Voila!!! you will have them both as one structure which is what is shown in the Further to the Advance book..!
and yes!! the 1984 machine (JB's not Jim watson's) is a Pulsed Motor of one scale down to the Gray Motor in a way, as POWER Pulse is fed back to the SINGLE BATTERY...
all one needs to do is figure out the TRIGGER in each case...

There is one more hint i would like to bring to every ones notice.... refer John's website for the SINGLE BATTERY 1984 Machine ('WARNING HIGH-VOLTAGE ENERGISER') of JB:
if you closely observe the original picture there and compare it with the same photo used in the Advanced Hand book.. there is Capacitor Included in the new picture (absent in JB's old website photo for the same photo)..now ! what is different?? Yes both work but some thing in terms of configuration is required to be done in each case of the presentation, which is not mentioned for all!!! the new one that includes the Capacitor is meant for the Watson Machine which is more power ful:



Rgds,
Faraday88.

[Aaron Murakami]

I do not have a computer. I have one borrowed telephone and one borrowed iPad.

If I had the resources mentioned, I would not ask anyone for anything as I do not wish to be a burden to anybody.

How about Aaron Murakami? Is it a violation for him to do this kind of detail? I would pay for the download from the website if I can get the service. I would even pay for the paper and ink.

If I cannot get the Advanced Handbook from the people who put it out, that would leave me no alternative but use a third party.

Perhaps hard copies should be part of the sales selection for customers who want them...???

All I am asking for is to buy myself a copy. Who knows what I might discover.

What I do for Eric Dollard since he doesn't have a computer is I print out his powerpoints and books and I take them to a FedEx copy shop.
For about $5, they will make it spiral bound with a frosted cover and black or blue back cover.

For the printing, it takes a long time to print color both sides and I can't offer that service because it will tie up my personal printer.

As suggested by aln, if you put it on a flash drive and take it to a shop like that, they can print it out for you color on both pages and bind it for you.

We will be putting all our books on Amazon as paperbacks - just not enough hours in the day to get them all done fast. Plus, they all have to be reformatted for the paperback book templates. It is way more time consuming that it seems.

You can email Jeff at help at emediapress dot com and ask him if he is willing to do it for you and what he would charge to do that on top of the cost of paper and ink.

[wrtner]

Aln's solution in post 13 seems to be a solution.

But I find it beyond extraordinary that the author/publishers do not crank out some print-on-demand copies for the many people who don't like ebooks (which evaporate if the laptop crashes, is stolen or succumbs to a glass of orange juice spilt all over it).

[John_Koorn]

Hi Pete, this is repeat, have you irritated anybody today about getting the Advanced Handbook printed out so you can read it?

Hi Repeat, no, no one has responded. I suspect they drink perfume and when they poot they think it does not stink.

Well, I am going to find a third party who does not drink perfume.

I wished for a nice day to be nice to people, but I will not be nice.

I have not ordered anymore "things".

I wish to be friends with the forum but I do not drink perfume.

Too many irons in the fire will get you burned.

Hi Why-me,

This is a discussion thread for the aforementioned e-book, not a help site.

Can I suggest you contact the publisher with your request? http://bedinisg.com/contact.php

(Link taken from the site where the e-book is offered for sale)

John K.