Four Wave Mixing

[blackchisel97]

Hi Abusa. Very neat I can't tell if everything is connected right by looking at finished pcb but I believe that person which was helping you knew what to do. The only way to tell right now is to power it and check each oscillator with a scope, including 7th one - slow pulse, op amp and the output from modulator, after the transformer.
There is one pot which adjust the output, all other are trimmers to set the frequency. In the paper it says - dry battery only.
I wish John could shed a bit more light on this circuit. I'm still not sure about two oscillators frequencies.

Thanks
Vtech

[Abusa]

Hi I got someone to help me make the device, can anyone look at this to see if they are any mistakes. I thought they will be a nobe for changing the frequency is there ment to be one.

I also advice on the best way to power the device, I would like to be able to plug it into the mains. If by batteries, what batteries would be best.

[blackchisel97]

Hello. Here is a couple of scope shots from the output. I didn't take shots from generators since they're square wave of different frequencies. This is what I can see:


Abusa, could you put your files in different format such as JPEG,PNG or GIF. They seem to be pdf which I'll have to download first in order to see it.

Thanks
Vtech

[blackchisel97]

Hi, can someone look at this to see if I have built my device right[ATTACH]947[/ATTACH][ATTACH]947[/ATTACH][ATTACH]947[/ATTACH][ATTACH=CONFIG]948[/ATTACH]

Hi Abusa. Your channel waves look ok. Do you have low pulse timer and modulator running as well?

Thanks
Vtech

[ZPDM]

Abusa,

I can not offer advice on your circuit diagram, however I would recommend per your previous posts that you might also research both intravenous and liposomal formulations of vitamin C.

[Abusa]

Hi, can someone look at this to see if I have built my device rightCircuit_Diagram_04++.pdfCircuit_Diagram_04++.pdfCircuit_Diagram_04++.pdf

[Mostie]

BC not tried 2 & 3, waiting on 50 ohm resistors.

[blackchisel97]

Thanks for the reply blackchisel97, this information his vital we need to know the number of sessions and how long a person should be connected on to the device.

Blackchisel have you tried zapping any bacterria with you device.

Any word from John anyone, he should be here to give us some guide, at atleast till someone has been able to replicate his results.

Alot of people needing alot of of help.

Hello Abusa. No, I cannot afford a good microscope yet. If you're interested in fighting "incurable" viruses please check Energetic Forum and MMS thread. I did provide some info regarding this supplement or visit Genesis II Church of Health & Healing. I've been using MMS for few years with very good results. If you have any questions don't hesitate to ask.

Regards
Vtech

[Abusa]

Thanks for the reply blackchisel97, this information his vital we need to know the number of sessions and how long a person should be connected on to the device.

Blackchisel have you tried zapping any bacterria with you device.

Any word from John anyone, he should be here to give us some guide, at atleast till someone has been able to replicate his results.

Alot of people needing alot of of help.

[blackchisel97]

Looks good Mostie. Did you have any problems with oscillators 2 and 3? I couldn't get them running with 50 Ohm resistors and had to increase to 120 Ohm.

@Abusa. I don't know the answer to your question but I doubt one session will be enough.

Thanks
Vtech

[Mostie]

thanks Vtech, i fixed it, forgot to cut a track, running 3 out of 6 osc.

[Abusa]

I have almost completed my device, I just need a couple more component to e shipped in.

Can anyone tell me how long does some have to be zapped for in order to get rid of the HIV, does it take more than one session.

[blackchisel97]

Nice one BC, mine is on stripboard, however I am missing some parts, which 386 did you use, there seems to be serveral variants? my one may be faulty.

I use UTC 386.

Vtech

[Mostie]

Nice one BC, mine is on stripboard, however I am missing some parts, which 386 did you use, there seems to be serveral variants? my one may be faulty.

[Abusa]

Hi blackchisel97 congrats on finish you device, can you post more picture of the wave and let us know the frequency your are running.

Thanks