CPD mod - capacitor potentiometer diode modification

[James_Somewhere_In_Idaho]

Hi Patrick and Bob, et al

Bob, the reason I posted that photo, was because it is one John B. has as a design for his "Zero-Force" motor (directly out of his FEG book), and I had brought up the topic, on another thread, regarding setting up an oscillating frequency to run it, since the capacitor/inductor parts of the circuits resemble LC circuits, and the zero-force motor starts up on its own, with the magnets riding the flux of the coils in parallel with the rotor...and yes, you might still need switching, but maybe only as a way to provide feedback for the oscillations...Patrick, your design has the coils in parallel...John's has them in series...interesting. (hehehe...rubbing hands together...can't wait to try it out).

[min2oly]

Hi Patrick et al

I wonder if we could use that for this?

[ATTACH=CONFIG]5005[/ATTACH]

not bad, give this a spin...

core, no core... the key is MINIMAL ON time, use a different timing rotor with smaller magnets and a skinny core on the trigger coil - or use a hall sensor with tiny magnets, anything to use as little power/current as possible. Harvest the spike only do not waste the current...
Kind Regards,
Patrick A.

[BobZilla]

I see, with that explanation it makes more sense.

James I could see tuning becoming a challenge with a setup like that. Not that it could not be done but basically what is happening in your drawing is that the coil is not conducting UNTIL the cap fills and the resistance changes enough to discharge through the coil. To get multiple coils to sync up on that cycle might be difficult.

Anyway just a quick thought on it, not a deep analysis.

Similar to this.

https://en.wikipedia.org/wiki/File:T...on_3_300ms.gif

[James_Somewhere_In_Idaho]

Hi Patrick et al

I wonder if we could use that for this?

[James_Somewhere_In_Idaho]

Hi Patrick

Holy cow! I was thinking that before you even mentioned it! What are the odds!?! Thank you for sharing this.

[min2oly]

Hi Patrick

That is very interesting...the connections are a little hard to visualize, though. Would you be willing to post a schematic, please? Thank you in advance...

Hi James,
thanks for checking in...
Here's the schematic

In the vid i'm only using one transistor and one power winding on the primary coil.

Now replace the charge battery with a coil and a cap in parallel. That's it, even simpler than it sounds.

The CPD mod is not necessary, it just happens to be extremely efficient. Now, we can spin a rotor in this arrangement faster with the spike than It will spin with the "primary current coil" enough said right?
KR - Patrick

[James_Somewhere_In_Idaho]

Hi Patrick

That is very interesting...the connections are a little hard to visualize, though. Would you be willing to post a schematic, please? Thank you in advance...

[min2oly]

[BobZilla]

Nice video Patrick, thanks for sharing.

Question about what you are showing if you don't mind. So the cap in the last bit of the video (not the CPD but the output) is simply inline to feed the coil? What I mean is there is not cap dump trigger like build the cap and release but rather just the spike is going directly into the cap and the coil is directly connected as the output?

To put it another way the cap has no switching other than when the spike gets pumped into it it converts and releases into the back coil and makes the magnet jump?

Thanks

[min2oly]

This subject probably deserves another thread but I'll post it here since I am able to prove best using my CPD mod.
In short... I'm sending the spikes to a cap that is parallel to a coil and getting it to perform work where as if I do not use the cap, the same spike to the coil will not perform any work. This is just more proof of what John Bedini has been talking about using a Cap to convert the radiant energy.

Kind Regards,
Patrick A.

[min2oly]

i have 1 coil with 100 ohms and 1 with 47 ohms for base resistance.... they dont seem to get warm on mine , but i also have 3 watt resistors.... this coil have a regular trigger winding? you running it on 12v??

.... yeah - what Brodie says :-)

[min2oly]

Not talking about the same resistor. I am not home to do experiments this week but found a computer I was referring to the resistor in series not in parallel with the cap. I don't know how to be more clear, sorry. I was just using one power wind so not "resistors" I did the experiment as you showed in video. I do not have a scope. It may be time for some pics or a video when I get home. Thanks for assistance. Aln

I get it now...
since you have only one wire/one transistor try removing that resistor all together.
No scope is your enemy. this is not an easy one to tune w/o it because you need to find your freq then use the resistance and diode to retune w/in that freq.

although..... with one wire, try just the cap. No diode no resistors no pot.
KR - Patrick

[Brodie Gwilliam]

i have 1 coil with 100 ohms and 1 with 47 ohms for base resistance.... they dont seem to get warm on mine , but i also have 3 watt resistors.... this coil have a regular trigger winding? you running it on 12v??

[aln]

Hi Al & Brodie,
Thanks for doing this perhaps I left something out in the explanation. This is good do get it out in the thread. It will show my flaws and we can fix so others can follow.

Heated the resistor? what resistor.... there should be no resistor across the cap if you are doing this.

Are you guys both talking about the resistors just before the bases of each transistor?
you are both working on multi-filers right?

So when you say the resistor is heating up you mean "resistors" plural?

or are you talking about the resistor across the cap because the experiment calls for removing that one...
KR - Patrick

Not talking about the same resistor. I am not home to do experiments this week but found a computer I was referring to the resistor in series not in parallel with the cap. I don't know how to be more clear, sorry. I was just using one power wind so not "resistors" I did the experiment as you showed in video. I do not have a scope. It may be time for some pics or a video when I get home. Thanks for assistance. Aln

[dennis foyil]

Brodie, vtech {Blackchisel} has a youtube by the name of '6 filer solid state' that will do that. He is putting 4 amps through it, but he also has the trannies on a hell of a heat sink. impressive build. dennis sorry I could not get the link to post.