What are you interested in from TeslagenX

[Patrikas]

Thank Patrikas,

I'm just putting the final touches on an instructional video for the TeslagenX SG8 kit. Should be up by the end of the Easter break.

John K.

G,day John,
ive looked for that vid over the past week did i miss it somewhere ? thanks

[Patrikas]

Great John,

im sure im gunna need it when it comes to hooking up all the coil wires & front and back ends....cheers

[Allen R.]

Looking forward to seeing that John K. , Thanks.

al

[John_Koorn]

Thank Patrikas,

I'm just putting the final touches on an instructional video for the TeslagenX SG8 kit. Should be up by the end of the Easter break.

John K.

[Patrikas]

Just like to say thankx to Tom C and John K "Teslagenx" for their help with parts and kit i purchaced,

For anyone who is new to circuts like myself i recomend the circut board kit from Teslagenx...,
the instructions are thorough and easy to follow everything is packaged seperatley and labelled ....cheers

[Tom C]

the polycarbonate kits are not available any longer. I can manufacture one from scratch if you really want one. there is probably 100-150 hrs of assembly labor plus 4 to 6 grand in components and fabrication. do you have a way to power it, and do you have battery banks that can handle it? this really is not a small request or task....
Tom C

[why_me]

I would be interested in a complete 30 coiler fully tested and ready to run from the box.

[Tom C]

I would be interested in the plexi rotor for my Renaissance 10 coil kit.

and the Cap Pulser.

Monty

We have 10 coil plexi rotors available.... they are set up for scalar north ceramics, 3/4 inch width 7/8 depth. you get the rotor drilled for the 10 coil hubs and axle and 40 gauss matched scalar north magnets. you will have to modify your 10 coil by either removing the "U" braces or notching them to allow the magnet to pass. 375 with magnets 325 without. if anyone wants one send an email to sales@ teslagenx.com

Tom C

[Monty]

I would be interested in the plexi rotor for my Renaissance 10 coil kit.

and the Cap Pulser.

Monty

[MrRonsen]

Hi all,

I am also interested in a Optimum Discharge Circuit shown on page 46,47 in the intermediate book built by John Bedini !!!

i am building the circuit with arduino instead of 555,
all parts came today.. BD243C,TS7812,IRFP260..
BUT would be great to get a ready build brick for plug in the system.

tested cap discharge options:
spring buttons (metal leg with roller that gets pushed down an pushes a button that gets backposition by a spring) tested..
failed because of latching after a while
relays tested.. failed because of latching after a while
now i build that MOSFET thing..

[ZPDM]

Tom,

Please consider a Bedini Window motor kit as one of your products. Thx,

Paul

[Tom C]

I was just looking at that new kit I made today and thinking how nice a matching slave board out be ;-) .

I would also be interested in the 3 pole replacement rotor. I have what I guess we could call 2nd gen of those. It is the molded plastic version. Would the new rotor have 3 or 6 magnets? I modified my original to hold 6 but it was a Frankenstein looking mess to do it.

6 magnets
Tom C

[powermanch]

Hi all,

I am also interested in a Optimum Discharge Circuit shown on page 46,47 in the intermediate book built by John Bedini ,

John

[Tom C]

I'm with Woody,
Comparitor!
But please make available a small and large versions. Small for single 8 strand, large for 10 coilers.

James

@james
the small comparator will be the first one available..... for sure!

@woody

there are a couple of problems with the 3 pole kit per JB, #1 is the core is too small in the coil, 2 not enough wire can be added of the right gauge, and 3 wrong magnets. the rotor is the easiest to solve so that will be first.

Tom C

[James Milner]

I'm with Woody,
Comparitor!
But please make available a small and large versions. Small for single 8 strand, large for 10 coilers.

James