Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 10 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Page 81 of 81 FirstFirst ... 3171798081
Results 801 to 806 of 806

Thread: Plasma Ignition | Plasma Jet Ignition

  1. #801

    Connection to the top of each Spark Plug

    Quote Originally Posted by Aaron Murakami View Post
    Thank you for sending that!
    Ok, now I understand that hookup but I also thought we needed to connect the extra strong spark directly to the top of each non-resistor plug to get plasma?

  2. #802
    Networking Architect Aaron Murakami's Avatar
    Join Date
    Jul 2012
    Location
    Spokane, Washington
    Posts
    1,223
    Blog Entries
    1
    Quote Originally Posted by rokan View Post
    Thank you for sending that!
    Ok, now I understand that hookup but I also thought we needed to connect the extra strong spark directly to the top of each non-resistor plug to get plasma?
    When you hook up the MSD/CDI, you are already getting a stronger spark at each plug - from coil, thru distributor directly to each plug.

    After the MSD/CDI is hooked up, then you add diodes. 4 of them.

    If you're coil isn't suitable for capacitive discharge, I'd recommend this one: https://www.amazon.com/gp/product/B0...SIN=B002Q363XM

    After getting the cdi/msd hooked up, post your results and then we can diagram the diodes to the top of the plugs. That will be super easy.
    Aaron Murakami





    You never change things by fighting the existing reality. To change something, build a new model that makes the existing model obsolete. ― Richard Buckminster Fuller

  3. #803
    A lot of work was necessary in order to support the Plasma engagement.

    Here are my first impressions:

    Trying to lean the fuel mixture, it is possible to intervene to the time the injectors are functioning.

    "Using a stock file from a 1992 G60 Passat syncro, and ECU temperature of 87 deg C, an IAT of 32 deg C and a battery voltage of 14, I get the following results adjusting the CO pot value:

    800 RPM at 37.5 mbar:

    CO pot setting vs Inj PW

    0 ; 3.102 ms
    200 ; 2.620 ms
    400 ; 2.540 ms
    495 ; 2.480 ms <-- value where fuel is neither added nor subtracted
    600 ; 2.416 ms
    800 ; 2.328 ms
    1000; 2.254 ms
    1200; 2.202 ms
    1400; 2.156 ms
    1600; 2.120 ms
    1800; 2.088 ms
    2000; 2.062 ms

    6300 RPM at 175 mbar:

    CO pot setting vs Inj PW
    0 ; 9.146 ms
    200 ; 9.088 ms
    400 ; 9.042 ms
    495 ; 9.030 ms <-- value where fuel is neither added nor subtracted
    600 ; 9.006 ms
    800 ; 8.984 ms
    1000; 8.960 ms
    1200; 8.950 ms
    1400; 8.938 ms
    1600; 8.926 ms
    1800; 8.914 ms
    2000; 8.904 ms

    These values would only come into play when the ECU is in open loop, otherwise the O2 sensor takes over.



    http://forums.fourtitude.com/showthr...ng-copot/page2 "


    In my system the limit is the setting at 1900 Ω.

    By doing this adjustment, (at 1900 Ω), I am observing the following phenomena:

    1) Plasma on/off and the needle of the tachometer jumps, just a little bit, so the system affects the operation. (This is at any fuel adjustment).

    2) The engine's temperature remains on the same level as in the normal fueling. (The normal value is at about 490-500 Ω).
    (This is checked only under very light duty, since I haven't the time to check it under normal or heavy operation).

    3) There is a substantial drop in the performance of the engine, especially at the high revs.

    4) The first measurements with the on board trip computer saw an, almost, vertical slope in the reduction of the consumption.

    Saying these, the only point for anxiety is the drop in the performance.


    Any thoughts?
    Last edited by Hellenic Vanagon; 05-18-2018 at 08:42 AM.

  4. #804
    Just in the case you know that nothing better can be done, please don't worry. The Plasma, in my case, supports the ignition functioning with the surface discharge spark plugs, which:

    1)Allow the use of the regular petrol 95 Ron instead of the super 98 Ron, without any compromise in the performance, (on the contrary, being immune to detonation and promoting a better combustion), the difference in Greece being ~ 20%.

    2)Reduce the consumption, at least, (I give the official estimation), 6%.

    3)Are susceptible to fouling if not supported by a proper, high energy, ignition, (here comes the Plasma).


    Thank you for your time, (and knowledge).

    Very happy with my Plasma.
    Last edited by Hellenic Vanagon; 05-18-2018 at 09:36 AM.

  5. #805
    (O.k., thinking about a water bubbler or a petrol fumes jar. Yes of course it works).




  6. #806
    just a quick post for a source for HV caps and diodes I've found:
    hvstuff.com
    they even have the HV wire discussed earlier in the thread

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •