Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Page 1 of 10 123 ... LastLast
Results 1 to 10 of 142

Thread: Bedini SSG Multi-Coil

Hybrid View

  1. #1
    Senior Member John_Koorn's Avatar
    Join Date
    Jul 2012
    Location
    Melbourne, Australia
    Posts
    1,077

    Bedini SSG Multi-Coil

    472667.jpg

    John Bedini's original 10 coiler

  2. #2
    from the pic, i see bridge rectf on the left below of the ten coiler.. is the gen coil to the primary, is one independent coil from ten coil or just take one strand from one of the coil? TIA

  3. #3
    Senior Member John_Koorn's Avatar
    Join Date
    Jul 2012
    Location
    Melbourne, Australia
    Posts
    1,077
    John and Peter did all sorts of experiments with the 10 coiler. Perhaps John can tell us what the bridge rectifier was used for.


    John K.

  4. #4
    Hi john

    I made 5 coiler and I cant save pictures in photo section to show you what I made this is my first multi straind multicoil bedini motor that is made on profi line scale I have problem with charging current that is 150 mA to 230mA at 2,1-2,5A in primary site???
    Is that normal becouse til now I allways had biger charging current ?????

    with regards stan

  5. #5
    Pictures of my build its not finishet yet but it will soon be


    Quote Originally Posted by stane View Post
    Hi john

    I made 5 coiler and I cant save pictures in photo section to show you what I made this is my first multi straind multicoil bedini motor that is made on profi line scale I have problem with charging current that is 150 mA to 230mA at 2,1-2,5A in primary site???
    Is that normal becouse til now I allways had biger charging current ?????

    with regards stan
    Attached Images Attached Images

  6. #6
    Senior Member Tom C's Avatar
    Join Date
    Jul 2012
    Location
    Pacific Northwest
    Posts
    1,888
    Quote Originally Posted by stane View Post
    Hi john

    I made 5 coiler and I cant save pictures in photo section to show you what I made this is my first multi straind multicoil bedini motor that is made on profi line scale I have problem with charging current that is 150 mA to 230mA at 2,1-2,5A in primary site???
    Is that normal becouse til now I allways had biger charging current ?????

    with regards stan
    Stane,
    Nice build. I assume the magnets are scalar north? if not then change them to scalar north. also all 3 of those copper bus pipes, need to have the ends tied together to for an inductance loop, especially the charge battery positive. also diodes should be voltage drop matched across the junction, resistors to bases should be exactly the same. your charging will go up if you close the charge battery positive bus.

    pleas post pics of collector after diode, trigger at base. want to see the slope of the trigger signal.

    Tom C
    Tom C


    experimental Kits, chargers and solar trackers

  7. #7
    Hi Tom C

    First: thanks for sugestions I was allways asking my self whay everybody has bus pipes tidet together when I wached the pictures from other builds.
    secondiods are mached litle ones from E to B are 0,498 V
    big ones 1n5408 are 0,569 V
    resistors are hybid made (ceramiks made in 0,5 % exact)thats 68,43 ohm (all of them)
    three: wrote down how many r60 rods I have in every core (125 rods) and howmany turns in every row on coil
    at the moment I have conected 4 coils the fifth one is not conected yet
    four: I dont know what you mean with scalar nort ?? did you mean super scalar north or just scalar north
    my arangment is all six pols are north facing out. with allmoust 3 kg havy rotor.
    Can you explain me what did you mean with:diodes should be voltage drop matched across the junction????

    first and second picture is taken from Colektor, pictur three is from base140920121936.jpg140920121935.jpg140920121937.jpg

  8. #8
    Senior Member Tom C's Avatar
    Join Date
    Jul 2012
    Location
    Pacific Northwest
    Posts
    1,888
    Quote Originally Posted by stane View Post
    Hi Tom C

    First: thanks for sugestions I was allways asking my self whay everybody has bus pipes tidet together when I wached the pictures from other builds.
    secondiods are mached litle ones from E to B are 0,498 V
    big ones 1n5408 are 0,569 V
    resistors are hybid made (ceramiks made in 0,5 % exact)thats 68,43 ohm (all of them)
    three: wrote down how many r60 rods I have in every core (125 rods) and howmany turns in every row on coil
    at the moment I have conected 4 coils the fifth one is not conected yet
    four: I dont know what you mean with scalar nort ?? did you mean super scalar north or just scalar north
    my arangment is all six pols are north facing out. with allmoust 3 kg havy rotor.
    Can you explain me what did you mean with:diodes should be voltage drop matched across the junction????

    first and second picture is taken from Colektor, pictur three is from base140920121936.jpg140920121935.jpg140920121937.jpg
    stane,

    scalar north is 2 north poles glued together, then that north to north is glued on edge, that is what provides the sharp switching.


    that thing looks like you have multiple trigger coils, and they are not matched. is there just one master coil? things are definately no alright on that machine, turn off all the coils except the master, do a scope shot, then add coils one at a time.

    Tom C


    experimental Kits, chargers and solar trackers

  9. #9
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,513
    Hi Tom C,

    What explains the 'Single turn' Inductance loop formation of the Copper bus bar? has it got to do with the coupling at the other end of the Scalar poles of the coil arrangement?
    I'm sure it has a Scalar implications ..but I'm baffled ..how..? kindly elaborate it for me..
    Thank you,
    Best Regards,
    Faraday88.

  10. #10
    Senior Member Tom C's Avatar
    Join Date
    Jul 2012
    Location
    Pacific Northwest
    Posts
    1,888
    Quote Originally Posted by Faraday88 View Post
    Hi Tom C,

    What explains the 'Single turn' Inductance loop formation of the Copper bus bar? has it got to do with the coupling at the other end of the Scalar poles of the coil arrangement?
    I'm sure it has a Scalar implications ..but I'm baffled ..how..? kindly elaborate it for me..
    Thank you,
    Best Regards,
    Faraday88.
    when the rotor passes thru the gap with the mag it closes the loop... is that what you are referring too?


    Tom C


    experimental Kits, chargers and solar trackers

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •