Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


PRE-REGISTER FOR THE*** 2018 ENERGY CONFERENCE ***

Results 1 to 8 of 8

Thread: Tesla 4 battery switch

  1. #1

    Tesla 4 battery switch

    Has anyone had any sucess with a Tesla
    4 battery switch ? Using 12 volt led acid
    Batteries?
    And electronic switching ?

  2. #2
    Member
    Join Date
    Jul 2012
    Location
    Long Beach, California
    Posts
    52
    By 4 batteries do you mean the first and second in series providing +24v power, the third one being charged with a load (motor turning conventional 12volt generator charging fourth battery) in series to the +24v and the fourth battery isolated from this circuit and running another load while also being charged as previously mentioned?

  3. #3
    Hi Richard,

    Quote Originally Posted by Richard View Post
    By 4 batteries do you mean the first and second in series providing +24v power, the third one being charged with a load (motor turning conventional 12volt generator charging fourth battery) in series to the +24v and the fourth battery isolated from this circuit and running another load while also being charged as previously mentioned?
    No. I think he is referring to what is discussed in this thread on the so called "Tesla switch". http://www.energyscienceforum.com/showthread.php?t=2071

    I think you are confusing this with the "Bedini SG - Beyond the Advanced Handbook" unit Peter Lindermann demonstrated at the 2016 energy conference. It used a three battery supply (plus one battery at rest) and a battery swapper. Each battery, when rotated into the charge position, was charged with both the run current followed by a radiant spike.


    @ Nic:
    There have been a few successful replications, and some with 12 volt lead acid batteries as best I can recall.
    Last edited by Gary Hammond; 10-18-2017 at 02:51 PM. Reason: add more info
    Gary Hammond,

  4. #4
    Senior Member Tom C's Avatar
    Join Date
    Jul 2012
    Location
    Pacific Northwest
    Posts
    1,885
    I have achieved unity while running loads. have not gone over.... the TS I have runs on a nine volt, and that runs down...


    Tom C


    experimental Kits, chargers and solar trackers

  5. #5
    Member
    Join Date
    Jul 2012
    Location
    Long Beach, California
    Posts
    52
    Quote Originally Posted by Tom C View Post
    I have achieved unity while running loads. have not gone over.... the TS I have runs on a nine volt, and that runs down...


    Tom C
    Tom, when you say you achieved unity, does that include the load or is the load over and above?

  6. #6
    Senior Member Tom C's Avatar
    Join Date
    Jul 2012
    Location
    Pacific Northwest
    Posts
    1,885
    Richard,

    I was able to run a load and keep the batteries charged, however the 9 volt that powers the 3524 and the switching eventually runs down, and the load I was running was very small. I would need more power out of the TS to charge the 9 volt and run a load. perhaps there is a way to have a cap bank charge up while the load is running to run the TS.

    Jeffrey Joseph who is on this forum has helped us with prototyping and he has had much better luck than I have, perhaps he will chime in. we finally have a board we feel we can sell and a kit coming soon.



    Tom C
    Last edited by Tom C; 10-21-2017 at 11:21 AM.


    experimental Kits, chargers and solar trackers

  7. #7
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,149
    Quote Originally Posted by Tom C View Post
    Richard,

    I was able to run a load and keep the batteries charged, however the 9 volt that powers the 3524 and the switching eventually runs down, and the load I was running was very small. I would need more power out of the TS to charge the 9 volt and run a load. perhaps there is a way to have a cap bank charge up while the load is running to run the TS.

    Jeffrey Joseph who is on this forum has helped us with prototyping and he has had much better luck than I have, perhaps he will chime in. we finally have a board we feel we can sell and a kit coming soon.



    Tom C
    Hi Tom C ,
    wonder why can'nt we tap from the 'powering' Battery to run the SG3524 PWM chip.. that way we keep the Batteries fresh all along..? and that way acheive over unity?
    Rgds,
    Faraday88.
    'Teaching can endure a quest for knowledge..but Learning solves an anomaly'

  8. #8
    Quote Originally Posted by Nic Bailey View Post
    Has anyone had any sucess with a Tesla
    4 battery switch ? Using 12 volt led acid
    Batteries?
    And electronic switching ?
    I think what you mean is on page 5, "The Tesla Switch" :
    http://www.free-energy-info.com/Chapter5.pdf
    I have heard it suggested that mechanical switching is preferred. The sparking and arcing might contribute in some way.
    Last edited by wrtner; 10-23-2017 at 09:58 AM.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •