Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 10 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Page 28 of 30 FirstFirst ... 182627282930 LastLast
Results 271 to 280 of 291

Thread: Kromrey Disclosure - Bedini SG - Beyond the Advanced Handbook by Peter Lindemann

  1. #271
    The Light Bulb in the trigger circuit acts like a variable resistor, as the primary battery's run down, and the rpm changes, the Bulb's filament resistance changes, keeping the circuit in tune... a very OLD School way of doing things from back in the Vacuum Tube days...

    You have to pick the correct size bulb, for the size of SG/SSG you are building, so that it glows about 3/4 bright at the Highest Primary Battery voltage, and about 1/3 bright at the lowest Primary Battery voltage.
    Last edited by RS_; 04-24-2018 at 09:31 AM.

  2. #272
    Thanks again for the info,

    I just never seen much of JB's early work even though I do have his early first book and still reading through it. I'm ready to check out my machine after replacing the base resistors with 100 ohm .1%, that should keep the base resistance the same in each circuit.

    Just heard from Tom C. and my drive coil and more coil forms and holders are ready to ship. Now I will be able to get this beast running with all six coils.

    Now to order for more wire. I dug out my Flowcode programmer that I used in college to learn to program devices like PIC, dsPIC, ARM and can do Raspberry Pi and Arduino. Working on different parts of project at the same time when I can.

    Take care,

    Richard (rdvideo)


    Remember what Einstein said, "Imagination is more important than knowledge."

  3. #273
    OK, couple more questions on multi-coil SG.

    Now that I have the drive coil that I wanted a while ago, I connected it up and started to find the right distance from coil to rotor. According to the SG books, finding the right distance is the first thing to do to get max speed at low current in. Then continue with fine tuning the trigger. Since I have not seen any videos by JB describing a multi-coil SG setup, do you setup the distance with the drive coil before adding a second genny coil and adjust the trigger or after the second coil? I need a little clarification on how to fine tune a multi-coil SG setup. With the right coil to start with and I have the base resistors at 100 ohm .1% for matching with the matched transistors in the 8 transistor kit from Teslagenx and the 1k ohm 5 watt pot as described in the SG books, I am ready to start fine tuning my setup or try too.

    I started playing around with the new drive coil and right now get close to 800 rpm's and two pulses, still playing around but getting late. Have to wait till weekend to have more time to play with this thing but I need to balance the second rotor I received because there is just a slight side "wobble" that is enough to vibrate the cart at high rpm's.

    Back later...

  4. #274
    Make all drive coils the same distance from the rotor. Closer means a stronger trigger signal, farther away means a weaker trigger signal.....
    Get it all tuned in and stable single pulsing, and where it will start up and ramp up in RPM to single pulse speed with out adjusting anything at a low battery V. Then add and adjust the genny coil distance, to see how that changes the RPM and current draw. A SG/SSG with a genny coil load should slow down the RPM and lessen the current draw to start with, and sometimes the RPM comes back up some, while the current draw stays about the same.

    Not sure which SCH you are following, but it needs at least a 5-10 ohm resister after the 1K 5W Pot, so you don't burn the Pot at its lowest setting, and add a Lamp for tuning as the batt's run down..... In some cases the Lamp can be added in parallel with the Pot, or another value of resistor, to get it to tune in correctly when adding a lamp....
    Last edited by RS_; 05-10-2018 at 05:19 PM.

  5. #275
    Hi RS,

    Thanks for info. When I first built the bicycle wheel version with a Bifiler coil that I made, I eventually made one more and added it to the setup opposite to the drive coil. You get it at the right position from the rotor, the RPM really started to take off faster than the one coil by itself. This is as far as I could go because funds disappeared at the time. I am using a new 12v Deep Cycle battery (125 AH) for the primary and an old car battery from my truck for the charge battery that measures 9.5v. I bought two Deep Cycle batteries at the same time to use to tune my setup with one coil, but need to discharge one battery to use as charge battery but no inverter yet to discharge it. That's why I am using the car battery which is smaller in size as compared to the other battery and thought to see if this setup will desulfate it and make it usable again; I've been watching some of JB's videos from the vacuum series.

    For the transistor base resistor, I have been following information in the SG books to see what happens and other info that I have. But, to put a small value resistor in series with a pot is standard electronics and the fixed resistor is determined by what application that it is needed in. The 100 ohm resistor as the shunt has shown that it is the right resistor because it takes higher resistance to tune the ckt as I have seen in my experimentation's with what I am working with.

    More questions to come, getting late...

    Take care...

    Richard

  6. #276
    OK,

    Storms around messing up my satellite internet. I am using the 8-transistor kit from Teslagenx and the second half is to be used with the genny coil that I have been playing with all these months. The genny coil has 5 wires and was wondering how I can use the fifth wire in my setup. Connect it parallel with another wire, or something that I have not seen before is just connecting the other end of the coil with diode as in RS info with four batteries.

    Just getting ready to try a 2-coil SG and making sure doing things right.

    Here goes nothing...

  7. #277
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,329
    Quote Originally Posted by rdvideo View Post
    OK,

    Storms around messing up my satellite internet. I am using the 8-transistor kit from Teslagenx and the second half is to be used with the genny coil that I have been playing with all these months. The genny coil has 5 wires and was wondering how I can use the fifth wire in my setup. Connect it parallel with another wire, or something that I have not seen before is just connecting the other end of the coil with diode as in RS info with four batteries.

    Just getting ready to try a 2-coil SG and making sure doing things right.

    Here goes nothing...
    Hi rd video,
    You can either parallel the Genny coil or series them for 'Back-pop' use, based on how your 8 strand SG is configured. get the jist of what that means and boy!! you are there.. good luck!
    Rgds,
    Faraday88.
    'Teaching can endure a quest for knowledge..but Learning solves an anomaly'

  8. #278
    Richard,

    There are a couple of things you can do with the 5 strand coil...

    1. put all 5 strands in series adding for a Genny coil hooked to a Cap pulser, LED Bank, etc....

    2. Make a PL 2016 conference version like I did in my 2017 conference presentation, with 1 drive strand and 1 trigger, and 3 output strands into 3 diodes to back pop the drive battery, or another battery.....

    there are other things you can do, but these 2 are the best choices....
    Last edited by RS_; 05-16-2018 at 08:11 PM.

  9. #279
    Thank you Faraday88 and RS again for the info.

    I'm still trying to understand the series connections of wires as PL explained in the third SG book and why not just use one piece of wire for the multiple length used? Have to re-read the book, trying to do too many things at the same time, home and project. Have to order for the 3060's diodes and look into Cap pulser as explained in Part 37, The Linear Amplifier Regulator from JB's DVD's. With information given, I will experiment and record everything done with scope pics.

    The only other thing I have to think about is what a 6 coil SG can do and how to approach it. Just get the basic unit working and decide from there.

    Thanks again for the info and take care...

    rdvideo

  10. #280
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,329
    Quote Originally Posted by rdvideo View Post
    Thank you Faraday88 and RS again for the info.

    I'm still trying to understand the series connections of wires as PL explained in the third SG book and why not just use one piece of wire for the multiple length used? Have to re-read the book, trying to do too many things at the same time, home and project. Have to order for the 3060's diodes and look into Cap pulser as explained in Part 37, The Linear Amplifier Regulator from JB's DVD's. With information given, I will experiment and record everything done with scope pics.

    The only other thing I have to think about is what a 6 coil SG can do and how to approach it. Just get the basic unit working and decide from there.

    Thanks again for the info and take care...

    rdvideo
    Hi rdvideo,
    Please read Tesla's Patents.. Study what Coils do and the various geometry they can be wound in.. now, that would tell you how to intercept the bloch wall and sipon the Radiant Energy...it is the bloch wall that we are all after and how to flex it. Imagnie if the wire were strainght and not coiled..where would be the bloch wall of such a geometry of the wire? is that not coinciding with Current in the coil and now additive to it..once you are able to do that you have made use of the normally wasted component of the Electromagnetic Field..
    The reason for what you asked 'why not use a single wire'...if you do that you are in essence undoing the acts Asymmetrical gauging the Induced e.m.f
    perhaps you could still do that if you maintained a parameter of one order..guess what that could be??
    Rgds,
    Faraday88.
    Last edited by Faraday88; 05-15-2018 at 11:29 PM.
    'Teaching can endure a quest for knowledge..but Learning solves an anomaly'

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •