Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 13% OF THE SEATS ARE AVAILABLE!!!*** 2017 ENERGY CONFERENCE ***

Page 9 of 11 FirstFirst ... 7891011 LastLast
Results 81 to 90 of 104

Thread: Bedini RPX Sideband Generators

  1. #81
    Networking Architect Aaron Murakami's Avatar
    Join Date
    Jul 2012
    Location
    Spokane, Washington
    Posts
    1,120
    Blog Entries
    1
    Solavei
    Quote Originally Posted by Oliver01 View Post
    Hello Aaron

    Just to say my rpx finally arrived, very excited to test it out now.

    A previous question of mine seems not to have made it here. What is the reason you guys chose the low power output vs the 10+ watt power of John's machine that you demo in one of your videos?

    I understand it may not be necessary but would be nice to understand the thinking?

    Regards

    Oliver
    Hi Oliver,

    We're sure it will meet your expectations!

    The 10 watt unit is too hot.

    The small power units are strong enough.
    Aaron Murakami





    You never change things by fighting the existing reality. To change something, build a new model that makes the existing model obsolete. ― Richard Buckminster Fuller

  2. #82
    I would like to experiment with a sweep that is cycles slower than the standard one so Hz would hold for a longer duration.

    Would changing 0.1 speed to 0.01 slow it down or do I change another setting like Step from 100 to 10 on the HPG1?

    Thanks

  3. #83
    Networking Architect Aaron Murakami's Avatar
    Join Date
    Jul 2012
    Location
    Spokane, Washington
    Posts
    1,120
    Blog Entries
    1
    Quote Originally Posted by jmkwisc View Post
    I would like to experiment with a sweep that is cycles slower than the standard one so Hz would hold for a longer duration.

    Would changing 0.1 speed to 0.01 slow it down or do I change another setting like Step from 100 to 10 on the HPG1?

    Thanks
    Exactly.

    That is really slow.

    0.1 will cycle through the ranage (if using 100hz to 150khz) in about 7-8 seconds
    0.05 will cycle in about 14-16 seconds
    and so on...

    If your desire is to get longer resonance at each frequency, then you have the right idea.

    You could also narrow the sweep range and then you will hit each frequency more often in the same time by leaving the 0.1 speed so different ways to do it.
    Aaron Murakami





    You never change things by fighting the existing reality. To change something, build a new model that makes the existing model obsolete. ― Richard Buckminster Fuller

  4. #84
    Thanks.
    I was hoping that would work without messing up the RPX concept.
    And yes, longer Resonance is my goal.

  5. #85
    Hi Aaron, I would like to ask you a few questions about the coil you made in the "How to Setup the RPX" Video.

    Q1

    What size was the wire you used to make the coil it looked about 18 AWG? Also, you mentioned that John recommended a heavier gauge then what was used in the video. What was John's recommendation for the lower gauge?

    Q2

    Any advantages to a lower gauge wire considering the output wattage?

    Q3

    Why don't you recommend using the Tesla Bifilar? The video's I have watched seem to indicate the bifilar is more efficient.

    Thank you for your time.

  6. #86
    Networking Architect Aaron Murakami's Avatar
    Join Date
    Jul 2012
    Location
    Spokane, Washington
    Posts
    1,120
    Blog Entries
    1
    Quote Originally Posted by Teslad View Post
    Hi Aaron, I would like to ask you a few questions about the coil you made in the "How to Setup the RPX" Video.

    Q1

    What size was the wire you used to make the coil it looked about 18 AWG? Also, you mentioned that John recommended a heavier gauge then what was used in the video. What was John's recommendation for the lower gauge?

    Q2

    Any advantages to a lower gauge wire considering the output wattage?

    Q3

    Why don't you recommend using the Tesla Bifilar? The video's I have watched seem to indicate the bifilar is more efficient.

    Thank you for your time.
    Hi,

    1 - This is 5kv insulated wire and works fine. Even with 1 foot thinner wired alligator clips and using an ohm meter, the entire thing is under 1 ohm. I do not believe thicker wire is needed. A 2 oz per square foot copper pcb with a spiral of 40 turns, 6 inches in diameter with 1mm thick traces (1mm thick space between traces) works fine as well and I can verify with the spectrum analyzer that it broadcasts everything just fine.

    2 - I don't believe there is any. I should edit the video or at least check that I'm relaying what John mentioned, but again, I see no benefit.

    3 - I haven't tried the bifilar method - all of John's were done with a single winding and that is what he recommended to me.

    I hope that helps.
    Aaron Murakami





    You never change things by fighting the existing reality. To change something, build a new model that makes the existing model obsolete. ― Richard Buckminster Fuller

  7. #87
    Thanks Aaron. That answered my questions. The PCB idea sounds interesting. I never noticed how cheap PCB engravers have become. I am also guessing that you would use a single sided board is this correct. Lastly, do you happen to have a PIC of such a board I would love to just have a look. Thanks for you time and help.

  8. #88
    Networking Architect Aaron Murakami's Avatar
    Join Date
    Jul 2012
    Location
    Spokane, Washington
    Posts
    1,120
    Blog Entries
    1
    Quote Originally Posted by Teslad View Post
    Thanks Aaron. That answered my questions. The PCB idea sounds interesting. I never noticed how cheap PCB engravers have become. I am also guessing that you would use a single sided board is this correct. Lastly, do you happen to have a PIC of such a board I would love to just have a look. Thanks for you time and help.
    It would be a 2 sided board.

    The bottom side would be to channel the center of the spiral to the other side and then a trace up to a corner to pop out the top near the outside winding trace.
    Aaron Murakami





    You never change things by fighting the existing reality. To change something, build a new model that makes the existing model obsolete. ― Richard Buckminster Fuller

  9. #89
    This is off-topic...is it possible to overcharge either the Velleman Generator or the 12-volt Talent Cell?

  10. #90
    Networking Architect Aaron Murakami's Avatar
    Join Date
    Jul 2012
    Location
    Spokane, Washington
    Posts
    1,120
    Blog Entries
    1
    Solavei
    Quote Originally Posted by jkeesey01 View Post
    This is off-topic...is it possible to overcharge either the Velleman Generator or the 12-volt Talent Cell?
    The Talentcell - I don't think so. The light changes from red to green when it is done.

    The Velleman, I don't know. The charging light stays red no matter how long I've had it on there.
    Aaron Murakami





    You never change things by fighting the existing reality. To change something, build a new model that makes the existing model obsolete. ― Richard Buckminster Fuller

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •