Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Page 4 of 4 FirstFirst ... 234
Results 31 to 34 of 34

Thread: Who has done ANYTHING with success along this topic?

  1. #31
    I have gotten a Toyota 22R to stumble along for about a half hour 6-7 years ago. I was using 4 of the Ozzy Freedom cells with four electrodes instead of 2 in each. Lye for electrolyte. Had a 10amp fuse on the cells. Started on gasoline then turned off the fuel pump. Was bubbling air through the cells and feeding into the intake through a vacuum port. I was expecting to retard the timing as the gasoline ran out but ended up advancing to 25degrees BTDC for the best stumble. The experiment ended when the electrodes melted!!
    Its gonna be about a month before I get back to it but am going to attempt to run a propane camp stove next so I can actually observe the flame.

  2. #32
    Who has done ANYTHING with success along this topic?
    I did. I made this hydrolysis device some years ago:


    Its a lead-acid battery in construction except its group of plates are all 316L stainless steel. It was my first ever venture into the HHO quest. It runs even better on 24 volts. It produced at least around 5 lpm of gas iirc. In my observation, that design is more efficient than the amp hog cells with lots of neutral plates in between the positive and negative plates. I had no knowledge of electronics back then, and it can work without the ordinary PWM, and the person I followed said that the particular 12v PWM he and others made doesn't affect gas output and now I can believe that. Its amps can be controlled with the concentration of the electrolyte. I used NaOH.

    Anyway, I used it in my Hilux diesel truck (with clamps, a bubbler, tubings, fat wires, amp gauge, switch, and all) until 2011 when I had to take it out for engine repairs. It used to give me around 25% of fuel economy at my personally observed sweet spot of 10 - 13 amps. More than 10 - 13 amps start to make significant impact and the alternator starts drawing proportional amounts of engine power to output those amps, more gas is produced but the alternator's drag nearly cancels out the effect. The mileage improvement was the same around 25% even at 30 amps. 30 or more amps makes things less practical / more expensive so I didn't try for more. I learned that by damaging the alternator by giving it 50-55 amps once, and even at 50 it didn't really blow up my skirt, so to speak.

    I did not feel enough compulsion to spend days and install it back again. I've got a wife and kids now and the economy is circling the drain so I have to spend all the time earning money to survive and doing so many chores all day, you know. I still have the apparatus and I've cleaned it up and tested it last month. I intend to install it to augment my biogas supply for the generator power system at home to make the engine run even more smoothly because I believe HHO in biogas will negate the retardant effects of the CO2 and the moisture in the biogas.

    The gas is highly explosive and a bit dangerous because it is quite likely to "flash back" after ignition and destroy the electrolysis chamber and that is why bubblers are always used with it and not the generic flash back arrestors. I know as the first hydrolyzer I made got destroyed due to a flashback by the end of the first test drive in my truck and I had to build a new clear PVC container to continue.

    Now my two cents worth speculations on the future of this tech? I've been following along off and on and read various stuff on HHO. One thing is definite, that the frequency and waveform of the current has an impact on production. My device does not work with 25 volts of alternating current but rig in a diode bridge and it'll immediately fill up the chamber with foam. This is what lead me to research the effect of the form of electricity. High pressure DC pulsing at high frequencies, I'd give that a try, and with that I could try to hit the elusive sweet spot of resonance, as some people would show on youtube. As for the electrolysis chamber design thats another thing thats open to improvement and research. I would definitely give the tubes-within-tubes Joe cell design a try before anything else. Plates like battery plates indeed have leakage currents that can waste energy. Besides, some resonance of water theories now floating around the web would require a Joe cell to work anyway. Last but not least, some people swear by the electrode material they use for hho generation. A photocatalyst effect is what they call it but I feel they fail to explain it really. Some are even offering TiO2 coating services for electrodes (youtube). Some use carbon electrodes / carbon fiber plates to demonstrate how they can manage to get electrolysis going with negligible amounts of electricity and with pure water as the electrolyte (which is something I find fascinating).

    I would also like to feed it the radiant energy / cold electricity coming out from my monopole SSG and observe. My SG is currently disassembled because I needed a better wheel to make it go faster. Thats the only way for me to be certain and share info if and how it will affect hho generation.

    If I get around to pursue hho tweakings and improvement any further, and if I find anything, I'll be sure to spread it in a hurry and make it open source asap. Personally, I feel I should buy a percheron horse, two thoroughbreds and other beasts of burden and forget about this entirely. I live in the countryside and I have a farm so..
    Last edited by Quigon10101; 12-25-2013 at 08:53 PM. Reason: % sign and typos

  3. #33
    people continue to invest on hho cells for have bad results.. there are inventors around the world that are working from years on hho cells without any good result. What you have to understand is .. I want make an different energy source but actually if you want substitute carbon you need to use nitrogen.. make ammonia on demand can be an great solution... But all peoples are oriented to ONLY make HHO .. But how many peoples know that hho cell produce a lot of carbon monoxide thanks to the steel interaction?? Apart make hho cells you must consider to unsderstand how these effectively work and what these produce. You can check simply if my words are an fake buying an low cost monoxide carbon instrument on internet and you found that you make more than >1500ppm of CO. That in all hho cells present on market. In this way you produce not only H2 O2 but also CO as output gas.

  4. #34
    No sense to spent money and energy for make hho. HHO is just an energy consumer. HHO business is stopped. There are other solutions for make new independent fuel.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •