Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 39 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: SG8 Pot location

  1. #1

    SG8 Pot location

    I understand for to tune the SG8 that you need to replace the 470 ohm base resistors with 100 ohm base resistors. On what area would I place the pot on the SG8? Here is a pic of mine:

    sg8.jpg

  2. #2
    Senior Member Tom C's Avatar
    Join Date
    Jul 2012
    Location
    Pacific Northwest
    Posts
    1,888
    place the potentiometer in the spot where the 12 ohm resistor is.

    Tom C


    experimental Kits, chargers and solar trackers

  3. #3
    Hi Yoe777 and Tom,

    still not clear to me where to put the pot... here a pic of mine, could you explain where exactly put the pot ? From where to where...
    I put numbers to make it easier to explain.
    please help
    thank you


    IMG_7368.jpg
    Last edited by claudio; 03-31-2018 at 09:55 AM.

  4. #4
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,284
    Quote Originally Posted by claudio View Post
    Hi Yoe777 and Tom,

    still not clear to me where to put the pot... here a pic of mine, could you explain where exactly put the pot ? From where to where...
    I put numbers to make it easier to explain.
    please help
    thank you


    IMG_7368.jpg
    Hi,
    Remove the 12 Ohm resistor and put the Potentiometer there...
    Rgds,
    Faraday88.
    'Teaching can endure a quest for knowledge..but Learning solves an anomaly'

  5. #5
    Senior Member Yaro1776's Avatar
    Join Date
    Aug 2012
    Location
    Heart of Vermont
    Posts
    261
    Quote Originally Posted by claudio View Post
    Hi Yoe777 and Tom,

    still not clear to me where to put the pot... here a pic of mine, could you explain where exactly put the pot ? From where to where...
    I put numbers to make it easier to explain.
    please help
    thank you


    IMG_7368.jpg
    Claudio - in your picture the adjustable pot goes between terminals 2 and 4 replacing the 12 ohm resistor.
    Yaro

    "The Universe is under no obligation to make sense to you." -Neil Degrasse Tyson

  6. #6
    Thank you guys, will try and post the results !

  7. #7
    Quote Originally Posted by claudio View Post
    Thank you guys, will try and post the results !


    I would leave the resistor - remove the trigger coil lead from 4 - place a pot between the trigger coil lead and terminal 4 of the 12 ohm resistor. make it a nice beefy POT. It's ok if you already did what they say worse case you burn the pot and run the circuit on the individual base resistors, I hope...

  8. #8
    thank you so much for your advices...
    I have another problem:
    I'm having difficulties to install the Analog Amp meters, what is the correct way? Do I need a specific shunt or is there another way to install them ?
    please help

  9. #9
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,284
    Quote Originally Posted by claudio View Post
    thank you so much for your advices...
    I have another problem:
    I'm having difficulties to install the Analog Amp meters, what is the correct way? Do I need a specific shunt or is there another way to install them ?
    please help
    You may simply place the Ammeter in series line of the side you want to measure the current at. like in line with the primary or secondary circuit.
    what is the scale- range of the Ammeter you have..?
    do you have one or two of these Ammeter. in that case you can have one at each side of the circuit.
    no need of additional shunts..

    Rgds,
    Faraday88.
    Last edited by Faraday88; 04-08-2018 at 01:33 AM.
    'Teaching can endure a quest for knowledge..but Learning solves an anomaly'

  10. #10
    yes right, in fact it was a non sense request...
    Ammeters are 0-3 A and 0-5 A I guess both will do the job..
    thank you again for the support !
    all the best
    claudio

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •