Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 2 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Page 2 of 9 FirstFirst 1234 ... LastLast
Results 11 to 20 of 89

Thread: SG8 Pot location

  1. #11
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,435
    Quote Originally Posted by claudio View Post
    yes right, in fact it was a non sense request...
    Ammeters are 0-3 A and 0-5 A I guess both will do the job..
    thank you again for the support !
    all the best
    claudio
    Hey,
    No questions are nonsensical..on the hind sight they are the most unsought after newbies but very vital to pondering minds go ahead with anything and what ever you feel to ask relevant to the forum.Yes, the range looks on high side but if your rig up is big scale machine and batteries then it makes perfect match with what you have.
    JB had a 5A output on his big 10 coiler. how big is your machine rig up?
    Rgds,
    Faraday88.
    Last edited by Faraday88; 04-09-2018 at 04:14 AM.
    'The Magnetic Field is the gatekeeper of the Wheather on the Earth'' - John Bedini.

  2. #12
    Hi Faraday88,
    my machine is a "Bike Wheel" Type with 21 magnets and about 63.5cm wheel diameter. One 7wire coil ordered from teslagenx site.
    it is turning at 260 rpm and charging easily 45mha batteries, input is about 1,8amps (1 ammeter installed, waiting for the second one ordered).
    I am still waiting ordered parts to improve the efficiency.
    I am having so much fun building it !
    If you have time I would appreciate very much if you could take a look at my project of the capacitors PCB as showed on the second book, are there any mistakes or ways to improve it ?
    regards
    cla


    sch.jpeg
    CapPCB.jpg

  3. #13
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,435
    Quote Originally Posted by claudio View Post
    Hi Faraday88,
    my machine is a "Bike Wheel" Type with 21 magnets and about 63.5cm wheel diameter. One 7wire coil ordered from teslagenx site.
    it is turning at 260 rpm and charging easily 45mha batteries, input is about 1,8amps (1 ammeter installed, waiting for the second one ordered).
    I am still waiting ordered parts to improve the efficiency.
    I am having so much fun building it !
    If you have time I would appreciate very much if you could take a look at my project of the capacitors PCB as showed on the second book, are there any mistakes or ways to improve it ?
    regards
    cla


    sch.jpeg
    CapPCB.jpg
    Hi Cla,
    Im more than happy to help you.. just some of my pointers:
    Read all the three books up close..it talks about the various experiments the JB did and what he found from them! in the intermediate book it talks about ''exploring'' pulsing the Cap at both the terminals..how do you think that can be affected? the diagram shown is half baked to help you understand the process..watch the pat# 6,545,444 you will get it i guess.It is called the full patent.(ask why?) Tom C calls it 'Ringing the bell twice'' I call it ''Space Switching'' it is the same thing happening in JB's 1984 single battery Motor-Energiser.. hope you get it..
    more as you learn and progress...
    Best Regards,
    Faraday88.
    Last edited by Faraday88; 05-01-2018 at 11:35 AM.
    'The Magnetic Field is the gatekeeper of the Wheather on the Earth'' - John Bedini.

  4. #14
    Quote Originally Posted by Faraday88 View Post
    Hi Cla,
    Im more than happy to help you.. just some of my pointers:
    Read all the three books up close..it talks about the various experiments the JB did and what he found from them! in the intermediate book it talks about ''exploring'' pulsing the Cap at both the terminals..how do you think that can be affected? the diagram shown is half baked to help you understand the process..watch the pat# 6,545,444 you will get it i guess.It is called the full patent.(ask why?) Tom C calls it 'Ringing the bell twice'' I call it ''Space Switching'' it is the same thing happening in JB's 1984 single battery Motor-Energiser.. hope you get it..
    more as you learn and progress...
    Best Regards,
    Faraday88.
    how is that pulsing at both terminals?

    and

    No, what you and Tom are talking about is not the same thing and surely not what JB meant by ringing the bell twice. However, if you think it is, please expand more descriptive rather than encrypted.

  5. #15
    Hi guys,
    My Bike wheel is up and running fine and I want to improve it.
    I am just trying to make it as simple as possible.
    I am trying to develop a working PCB to mount all the electronic parts for the capacitor module and continue to experiment, I am not a technician.
    The PCB for the "basic" machine was pretty easy to do, this one is more tricky.
    I have all the parts needed, now I just I need some help to avoid mistakes before sending the PCB to manufacturing..

    min2oly
    right! One pulsing terminal,corrected,do you see any other mistakes ?
    There are so many terminals (the real module from JB has only 3 terminals) and i am not 100% sure the transistors, timer etc. are correctly connected..

    thank you and best regards

    updated PCB
    sch.jpeg

    comp.jpg
    offmodule.jpg
    Attached Images Attached Images
    Last edited by claudio; 05-02-2018 at 04:10 AM. Reason: updated PCB

  6. #16
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,435
    Quote Originally Posted by min2oly View Post
    how is that pulsing at both terminals?

    and

    No, what you and Tom are talking about is not the same thing and surely not what JB meant by ringing the bell twice. However, if you think it is, please expand more descriptive rather than encrypted.
    Hey Min2oly,
    Switches are substitute for Capacitors in a way…(Tesla Impulse ) of one type of geometry i mean Temporal and NOT Spatial geometry of 3 co-ordiantes.. Temporal co-ordinates are Bipolar and directional so essentially you have w two type of Capacitors geometry. when you use the 1984 Single battery machine, you alter the ON-State and the OFF state side of the switching compared to what you when you use the SG in the full -regauge mode.
    I can also say that there is an equivalent sense to this when you need to charge the front/ primary and then you call that as 'Bridging the gap at once' where you need to isolate the SG circuit and from the dump Capacitor and completely connected to the primary battery.
    Yes..so Ring the bell twice at the secondary and Bridge the gap at once at the Primary... which is to Regauge Positive Radiant at primary and Negative Radiant at the secondary...two different Energies Asymmetrically Regauged.
    the complete circuit to ring the bell twice is present in plane sight in JB's Old sight and also in other patents that i studied that is not owned by JB.
    rest is all left to how any individual assimilates the concept.
    Best Regards,
    Faraday88.
    'The Magnetic Field is the gatekeeper of the Wheather on the Earth'' - John Bedini.

  7. #17
    Why don't you just show us which circuit you are talking about...

    your words usually make some sense I can grasp onto, I can't make sense of most you write here...
    there is a constant mixing of key words with skewed definitions that don't match...
    can you explain in simple layman's terms so we can all understand your point.

    Quote Originally Posted by Faraday88 View Post
    Hey Min2oly,
    Switches are substitute for Capacitors in a way…(Tesla Impulse ) of one type of geometry i mean Temporal and NOT Spatial geometry of 3 co-ordiantes.. Temporal co-ordinates are Bipolar and directional so essentially you have w two type of Capacitors geometry. when you use the 1984 Single battery machine, you alter the ON-State and the OFF state side of the switching compared to what you when you use the SG in the full -regauge mode.
    I can also say that there is an equivalent sense to this when you need to charge the front/ primary and then you call that as 'Bridging the gap at once' where you need to isolate the SG circuit and from the dump Capacitor and completely connected to the primary battery.
    Yes..so Ring the bell twice at the secondary and Bridge the gap at once at the Primary... which is to Regauge Positive Radiant at primary and Negative Radiant at the secondary...two different Energies Asymmetrically Regauged.
    the complete circuit to ring the bell twice is present in plane sight in JB's Old sight and also in other patents that i studied that is not owned by JB.
    rest is all left to how any individual assimilates the concept.
    Best Regards,
    Faraday88.

  8. #18
    Senior Member Faraday88's Avatar
    Join Date
    Sep 2012
    Location
    Bangaluru, Karnataka, India
    Posts
    1,435
    Quote Originally Posted by min2oly View Post
    Why don't you just show us which circuit you are talking about...

    your words usually make some sense I can grasp onto, I can't make sense of most you write here...
    there is a constant mixing of key words with skewed definitions that don't match...
    can you explain in simple layman's terms so we can all understand your point.
    Hi Min2Oly,
    Yes, thank you for your understanding!! i'm in the process of writting this Science and would eventually be ready with a book that speaks this Tesla's wisdom.
    My intention here is to teach the Tesla Wisdom by setting up pointers in the direction of experimentation to people who are inclined to understand the Science and not something like a spoon feeding and ready for a DIY situation..
    Over the years I have found that most patents speak the Science themselves at least in the cases of Radiant Energy.. why do'nt people who experiment read them even if they do it again and again..i did this for years..and thats how you learn..and believe me there is no subsituite to learning..because it teaches you more than the original ''feeding'' given to you.
    The beauty of a Patent is to Learn them... replicate them..ect... that's how i look at it.
    I gather the same spirit from most of the Moderator's here.. and i stand by them.
    Its not my intention to be rude, hope you understand my sentiments.
    Best Regards,
    Faraday88.
    'The Magnetic Field is the gatekeeper of the Wheather on the Earth'' - John Bedini.

  9. #19
    You see, now these words are comprehendable, your previous babble is not. You say you want to set up pointers however your pointers are aimless. I call BS you do not understand what you are talking about. You try to sound like you do but you don't. Let's turn this around and actually give some real explanations if you feel I am wrong. You say you are "writing this science" let's prove it, why not reword your last post so that it is comprehendible. and show us this circuit you talk about...

    Quote Originally Posted by Faraday88 View Post
    Hi Min2Oly,
    Yes, thank you for your understanding!! i'm in the process of writting this Science and would eventually be ready with a book that speaks this Tesla's wisdom.
    My intention here is to teach the Tesla Wisdom by setting up pointers in the direction of experimentation to people who are inclined to understand the Science and not something like a spoon feeding and ready for a DIY situation..
    Over the years I have found that most patents speak the Science themselves at least in the cases of Radiant Energy.. why do'nt people who experiment read them even if they do it again and again..i did this for years..and thats how you learn..and believe me there is no subsituite to learning..because it teaches you more than the original ''feeding'' given to you.
    The beauty of a Patent is to Learn them... replicate them..ect... that's how i look at it.
    I gather the same spirit from most of the Moderator's here.. and i stand by them.
    Its not my intention to be rude, hope you understand my sentiments.
    Best Regards,
    Faraday88.

  10. #20
    Hi Richard,
    thank you for your advice !
    Here the PCB corrected.
    Should the traces be even wider ?
    Any other suggestion ?
    In your opinion the chips are correctly connected ?
    Any other suggestion would be very much appreciated...
    all the best
    Cla

    comp.jpg
    Last edited by claudio; 05-03-2018 at 12:34 AM.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •