Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Page 3 of 3 FirstFirst 123
Results 21 to 27 of 27

Thread: Help SG3524 based charger

  1. #21
    Senior Member John_Koorn's Avatar
    Join Date
    Jul 2012
    Location
    Melbourne, Australia
    Posts
    1,077
    Hi Ed,

    That's much better. First of all, if you are going to build this circuit I encourage you to read and understand the patent where this drawing came from. It is attached to the post below.
    Now to your questions. All of the points you marked with red text are only test points. They do not connect to anything.

    Bedini_Cap_pulser_US20030117111_001.pdf



    Hallo Ed,


    Dat is veel beter. Allereerst, als je gaat om dit circuit Ik moedig u aan om te lezen en te begrijpen het octrooi waar deze tekening kwam uit te bouwen. Het is aan de post hieronder bijgevoegd.
    Nu op uw vragen. Alle punten die je gemarkeerd met rode tekst zijn meetpunten. Ze hoeven geen verbinding tot niets.

    Groet John K.

  2. #22
    Senior Member Ed_Morbus's Avatar
    Join Date
    Aug 2012
    Location
    Netherlands, The Hague
    Posts
    112
    John koorn thank you

  3. #23
    Greetings:

    There's a writeup on this unit, along with a pinout somewhere on Patrick Kelly's site: http://www.free-energy-info.com/

    I have built a few chargers based on this chip with good results.

    glen

  4. #24
    Hi,
    I just registered to this forum and found this topic where I can contribute to.
    Have you had any success on this topic?

    I have this circuit working at my place for the past 8-9 months powered off a solar panel.
    The difference being the absence of external antennae as described initially.

    Thanks.

  5. #25
    Quote Originally Posted by John_Koorn View Post
    Hi Ed,

    That's much better. First of all, if you are going to build this circuit I encourage you to read and understand the patent where this drawing came from. It is attached to the post below.
    Now to your questions. All of the points you marked with red text are only test points. They do not connect to anything.

    Bedini_Cap_pulser_US20030117111_001.pdf



    Hallo Ed,


    Dat is veel beter. Allereerst, als je gaat om dit circuit Ik moedig u aan om te lezen en te begrijpen het octrooi waar deze tekening kwam uit te bouwen. Het is aan de post hieronder bijgevoegd.
    Nu op uw vragen. Alle punten die je gemarkeerd met rode tekst zijn meetpunten. Ze hoeven geen verbinding tot niets.

    Groet John K.
    Hi John,
    Have you or anybody here made the DC to DC Converter, Center-tapped Coil Dual-Pulser, which the patent shows as Figure 2? Also in the SG Beginners Handbook pg 109 Fig. 2, energy source for feeding energy to Fig. 1, the 'full-Cap-dump'.?

    Please Help w DC to DC Converter JB Patent Fig 2 and also like Ismael Aviso uses.jpg

    No write-up at PKelly's site near JB's name, but pulser is mentioned. I want to wind this DC to DC Converter coil, and do not know how to start.

    I found JB's post here for Fic for SG3524 Circuit:
    http://www.energeticforum.com/renewa...html#post75195
    Re-Drawn in free Express Schematic: SG3524 Redrawn in Express Schematic too large so.jpg

    SG3525 $~2 ea US on EBay: EBay SG3525 PWM.jpg TIP 120's Darlington driver pair seem maybe OK Vs. Opto & BD243 driver pair for turning Off faster.

    I see this guy using JB's circuit here, famous, someone must have wound a DC to DC Conveter like Fig. 2 here? ? ???
    https://www.youtube.com/watch?v=wC6aglJ6a_8 " Free Energy : Ismael Aviso Electric Car Secret : Coil Shorting "

    Ismaels Secret is JBs DC2DC Converter like shown in SGBHBook Pg 109 Fig 2.jpg Does this look familiar?

    Anybody wanna build coils like this with me? I only need center-tapped coil help. This thread seems like bait and switch. I see no antenna in the patent at all. Probably missed it.

    Thanks in advance for center-tapped coil help for Fig 2 Replication,

  6. #26
    Quote Originally Posted by jonnaprabhu View Post
    Hi,
    I just registered to this forum and found this topic where I can contribute to.
    Have you had any success on this topic?

    I have this circuit working at my place for the past 8-9 months powered off a solar panel.
    The difference being the absence of external antennae as described initially.

    Thanks.
    Hi Jonnaprabhu,
    How did you make your center-tapped coil for the DC to DC energizer?

  7. #27
    Hi Volty,
    The DC-DC converter is intended to be used as an external power supply as described in the patent. In my case, I had a 12V 100W solar panel lying idle which I used as my power supply.
    That simplified things to a great deal because the main focus area was to get the SG3524 instead of the DC-DC converter.

    I started another thread where I am discussing my new design which is microcontroller based and I have had good success with it - http://www.energyscienceforum.com/sh...t=1961&p=17360
    There are no circuits that I have posted yet, but will, soon.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •