Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Search:

Type: Posts; User: Dieselship

Search: Search took 0.00 seconds.

  1. Hi Hobbyrobotik, The run/charge battery is...

    Hi Hobbyrobotik,
    The run/charge battery is about 275 cold cranking amps from Exide. I was running the Arduino on a 9v battery that kept draining after few hours. At one point I didn't realize...
  2. I used the following isolated module shown in the...

    I used the following isolated module shown in the link. The results were good. I was using a fully charged 12V battery for the test. The voltage was bouncing between 12.43V - 12.44V - 12.43V. I ran...
  3. Single Battery Bedini Using Isolated DC Supply Module

    I performed an experiment by charging and running the same 12V battery, using a 12V In/Out Isolated DC Supply Module and an Arduino Microcontroller. The circuit diagram has been attached. Arduino was...
  4. Hi jd_zinke, I have never tried with this...

    Hi jd_zinke,
    I have never tried with this type of a cap/battery at the front end. But it will be interesting to see the results. I use large Maxwell 16v cap bank with overcharge protection...
  5. Bob, I did some more tests today, but there is no...

    Bob, I did some more tests today, but there is no difference. I checked the polarity, reversed connections etc, but the behavior is the same. I cannot say for certain, but the issue is with cap1...
  6. Well, we all will have to rely on the internet...

    Well, we all will have to rely on the internet stores for all our electronics. It has be that way for a while now. I guess that is the new reality. Stores like RadioShack cannot survive in this...
  7. Bob, Thanks for the information on the CBA...

    Bob, Thanks for the information on the CBA software. What I heard is that all the Radioshack stores are not closing. Sprint is going to takeover part of the store and have their own display inside...
  8. Thanks Bob as always. I checked some of the...

    Thanks Bob as always. I checked some of the pictures of your design. Looks nice ! It's shape some how reminds me of the old Marconi Radio -:) I like your wiring design inside the unit. Looks neat....
  9. Bob, Sorry to hear about your event.. At least...

    Bob, Sorry to hear about your event.. At least your machine is safe. I also had a "thermal event" a few months back when I used Arduino with a Voltage Divider circuit. I was trying to check the...
  10. Bob, I think attaching the cap to NC Relay...

    Bob, I think attaching the cap to NC Relay position may work. I need to try it out and see if it works. It is also possible that the Solid State Relay can also fail.
  11. I appreciate your explanation on the Cap dump...

    I appreciate your explanation on the Cap dump Bob. I like your idea of using the Opto switched SS Relay. Mine is a cheap Chinese version. But it works well though.

    Bob did you ever try using a...
  12. Bob, Thanks for the explanation on the...

    Bob, Thanks for the explanation on the characteristics of the batteries while working with the Bedini circuit. It was really helpful for me. When I think back on the issues that I faced while...
  13. Bob, Thanks for the advice and information on the...

    Bob, Thanks for the advice and information on the voltage levels of the batteries. I like the way you have designed a separate wheel for the generator circuit.

    I have seen some posts about...
  14. Bob, Thanks for the advice on the neodynium...

    Bob, Thanks for the advice on the neodynium magnets. Actually I used neodymium instead of ceramic magnets since my plan was to mix the 8 filer Bedini spools with generator coil spools also. As I...
  15. Thanks Bobzilla. I agree you may have a point on...

    Thanks Bobzilla. I agree you may have a point on my clamp meter. I'll change it to an analog meter and check the results. The clamp meter shows "ac" when in current settings. I was not 100% sure if...
  16. Bedini current difference between run and charge battery

    I have build a bedini motor with an 8 filer cable with one wire acting as a trigger. There are 8 transistors that are pulsed. The motor works well in terms of charging the charge battery or a...
Results 1 to 16 of 16