Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Search:

Type: Posts; User: Buz86

Search: Search took 0.00 seconds.

  1. Replies
    394
    Views
    165,754

    oscillator

    Hi, was just wondering... Is there a reason you didn't twist the wire? Does it charge better if you just run all them parallel like the instead of twisted? Also, what gage wire is that? and your...
  2. OK so I guess it might have been a bad connection...

    OK so I guess it might have been a bad connection because it started to turn back on and then would stop eventually. I knew when it was working because I would hear the feedback from the coil that...
  3. Radiant Energy Powering of the Monopole Motor (pg. 47 Free Energy Generation Book)

    Howdy everyone. I recently decided to give the solid state circuit and the cap dump circuit in the book a try. I gathered all the components and first tried the solid state on pg 46. Couldn't get it...
  4. Replies
    6
    Views
    2,663

    I measured it and it was 9.6. Is this too much...

    I measured it and it was 9.6. Is this too much resistance? And I thought I had two but I found the other one today. It was about 1 foot away and connected to a spool that I started winding it around...
  5. Replies
    6
    Views
    2,663

    I want to say it is 26 awg. At one point I...

    I want to say it is 26 awg. At one point I thought I checked it with my digital micrometer and I took that decimal figure and it was in range for 26awg. Would that be too thick?
  6. Replies
    6
    Views
    2,663

    window motor big coil

    I was just curious if this coil here would work for the window motor one day when I get that far. I had an old SAE-400 Lincoln stick welder with a gas motor in it that went out so I took the thing...
  7. Replies
    5
    Views
    2,448

    I guess I should have been more specific too. The...

    I guess I should have been more specific too. The circuit I'm referring to is the one on page 46. This is the solid state charger right? And also, I see it has
    bd234c but on another page I saw it...
  8. Replies
    5
    Views
    2,448

    Are all the capacitors 450/500v rating? and what...

    Are all the capacitors 450/500v rating? and what about the resistors. What resistors should I use for bedini devices, 1 watt?
  9. Replies
    5
    Views
    2,448

    So the 200 ft (450 turns) trifilar 23 awg wire...

    So the 200 ft (450 turns) trifilar 23 awg wire from r-charge will not work for this? I would actually like to use the 18 I have for better charging but I want to follow the schematic exactly as it...
  10. Replies
    5
    Views
    2,448

    Free energy generation circuit question

    Hi I'm looking at the circuits in the free energy generation circuit and schematic book and I'm just wondering what the volt rating is on the capacitors in the diagrams. I see the uF but nothing for...
  11. Replies
    12
    Views
    3,710

    Oops, forgot the pictures 65106511

    Oops, forgot the pictures 65106511
  12. Replies
    12
    Views
    3,710

    Well I guess it isn't fried. I hooked it up this...

    Well I guess it isn't fried. I hooked it up this morning and it's working fine now. Here's my setup. I don't even have a neon on this circuit because it's on my other setup with the bike wheel at my...
  13. Replies
    12
    Views
    3,710

    Well maybe it isn't in attraction mode. I guess...

    Well maybe it isn't in attraction mode. I guess it could be that the magnets just tend to stick to metal and the core is metal. So maybe it's not in attraction mode but I do know that it isn't...
  14. Replies
    12
    Views
    3,710

    I thought that was it a couple days ago when I...

    I thought that was it a couple days ago when I couldn't get it to run so I went and bought 2 brand new transistors I soldered one to the circuit and when I spun the wheel I realized i had my neon...
  15. Replies
    12
    Views
    3,710

    Standard SSG help

    Hi guys, I was able to make 2 coils. a 20/23 on the standard size coil spool. and also a 23/26 on the mini coil spool. I was able to get the circuit working today. It works using either coil, but I...
  16. Replies
    1
    Views
    1,668

    Original North Pole Motor

    Hi guys, I was just wondering what the wire length needed would be to create the coil on the drawing that John initially gave to the little girl to build off. On the top it says North Pole Motor and...
  17. Replies
    3
    Views
    2,058

    Which build is the "original machine"?

    Hello everyone, I'm new to the forum but slightly familiar with the technology. I read about these machines and was immediately fascinated. So I ordered a prewound 23/26 cool and bought the parts....
Results 1 to 17 of 18