Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Search:

Type: Posts; User: Bradley Malone

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    1,522

    Rs, I absolutely agree with the smaller gauge...

    Rs,
    I absolutely agree with the smaller gauge statement. I just know from experience that it takes, what seems like, a hundred times more than you think it would. I cut a big pile of wires from the...
  2. Replies
    11
    Views
    1,522

    I have not done any comparison to see the...

    I have not done any comparison to see the difference, If any, in a bedini sg specifically. But one of my favorite sources for coated iron is green floral wire. It takes a LOT to fill up a core and I...
  3. Replies
    40
    Views
    4,917

    If it is only doing that when the wheel is...

    If it is only doing that when the wheel is spinning then it's normal. The magnetic effects on an air core coil are very fast and cause high speed oscillations. Putting a core in the coil slows down...
  4. Replies
    40
    Views
    4,917

    The high pitch noise is the oscillations...

    The high pitch noise is the oscillations happening in the coil. If it constantly whines, that means you still have it wired in a forced oscillation setup. Is either end of your trigger wire going to...
  5. Replies
    40
    Views
    4,917

    Faraday, I meant the non rotored version. If you...

    Faraday, I meant the non rotored version. If you take the coid from a machine with a rotor, stop the rotor and change the trigger wiring then the machine would oscillate without the magnets. But...
  6. Replies
    40
    Views
    4,917

    Let's start from step 1. Run battery disconnected...

    Let's start from step 1. Run battery disconnected and charge battery disconneced.....wheel stationary.

    When you connect power to the "run" battery nothing should happen. If the neons light up at...
  7. Replies
    40
    Views
    4,917

    If the neons lit up when you hooked the power to...

    If the neons lit up when you hooked the power to the battery then you have the trigger backwards and it is in a forced oscillation mode.
  8. Replies
    40
    Views
    4,917

    I will attempt to explain better. When the magnet...

    I will attempt to explain better. When the magnet is passing by the coil at low rpm, the change in magnetism is slow and takes longer. When it is slow the voltage induced into the trigger is low. As...
  9. Replies
    40
    Views
    4,917

    You would need to clarify what you mean by...

    You would need to clarify what you mean by nothing is working. When power is applied nothing should happen. The circuit should basically just sit and wait. When you spin the wheel by hand it will...
  10. Replies
    40
    Views
    4,917

    Yes. The battery is not done discharging. What...

    Yes. The battery is not done discharging. What you are seeing is the discharge "curve". When you initially load a battery the voltage will drop quickly. Then it will level out in the mid 12 volt...
  11. Replies
    56
    Views
    4,567

    Yep that's it.

    Yep that's it.
  12. Replies
    56
    Views
    4,567

    Think of it like a battery bank....if you need 24...

    Think of it like a battery bank....if you need 24 volts you put two in series....if they don't have enough current then you take another two that are in series and you take that 24 volts positive to...
  13. Well I'm not in Seattle but I occasionally travel...

    Well I'm not in Seattle but I occasionally travel there for training in Kirkland. I believe I may be making another trip that way sometime soon. If I do I'll let you know and can swing by and get you...
  14. Replies
    108
    Views
    13,597

    Good stuff deuis. Thanks for taking the time to...

    Good stuff deuis. Thanks for taking the time to document this stuff! Any information or data added to the cause is wonderfull.

    Off subject ...kinda.....but I always wondered, in a resonant tank,...
  15. Now that you posted the schematic it definitely...

    Now that you posted the schematic it definitely makes sense. As the cap fills the bias is equalized but since the "input keeps rising it is rebiased. Hmm... definitely interesting thanks for sharing!
  16. Deuis....can you explain what's going on with the...

    Deuis....can you explain what's going on with the diode coil setup? To my understanding the voltage would bias the diode junction and just let the energy flow...so what's causing the ringing effect...
  17. Deuis...that's interesting and I'll have to mess...

    Deuis...that's interesting and I'll have to mess with that later.

    However that appears to just be ringing. The bedini coil circuit I have set up is actually oscillation after the hall. Just the...
  18. Replies
    4
    Views
    1,884

    Got to ask " new lightweight high density...

    Got to ask

    " new lightweight high density energy storage devices"

    what is THIS. device?not asking for full disclosure of private informatation....a hint ;) or arrow in the right direction,...
  19. Alright I have got to say...synchronicity is a...

    Alright I have got to say...synchronicity is a thing :) (thanks for that post faraday)

    Thank you gary for chiming in here. seriously the posts make me totally feel different. I have honestly felt...
  20. One more note on this. The oscillations are...

    One more note on this.

    The oscillations are definately, in part, due to it being in the "pull" mode. Here is why. When I look on the scope there is the drop to 12 volts (I have the display...
  21. Glad Im not the only one :) It is extremly...

    Glad Im not the only one :)

    It is extremly hard for me to stick to one project. That is why I quit posting so much. I would start one thing and as soon as I saw what I wanted to know about it I...
  22. Thanks Faraday. As I stated before I started out...

    Thanks Faraday. As I stated before I started out with tight tolerances but my building skills were not enough for it. One little bump and the magnets would hit the cores and go flying. So I decided...
  23. Figured out what it was. This effect is dependent...

    Figured out what it was. This effect is dependent on two things.

    #1 the transistor. Not sure what exactly is different from the ones that work and the ones that don't. I know i noticed that the...
  24. Alright, well I did something stupid and tried to...

    Alright, well I did something stupid and tried to clean up the wiring and now this effect is not happening. Wanted to make everything more clean so that when I made a video it could be easier to see...
  25. Just wanted to add a small amount of info about...

    Just wanted to add a small amount of info about the rotor. the way it is setting in the picture is only because when the "effect" started I wanted to leave everything right where it was so I didn't...
Results 1 to 25 of 291
Page 1 of 12 1 2 3 4