Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Search:

Type: Posts; User: VortexTurtle

Search: Search took 0.00 seconds.

  1. Patrick, Good idea with the cam, I will give it...

    Patrick,
    Good idea with the cam, I will give it a try with the next vid and see if it works.
    The effect that I was getting with the flyback stopped about two hours after I posted it, probably...
  2. Proof that flyback is enough to sustain a self-runner

    Hey there all,

    Here is the rundown: I built a simple pulse motor similar to the one Lidmotor has. I have dubbed it "The Simple Amazing Pulse Motor". I have been playing with it for a week or so...
  3. I would suggest learning how the device is...

    I would suggest learning how the device is intended to function, and how it differs from other devices out there. I don't see how one can completely change the main component of one of his devices...
  4. longhorn, where did you get that analog meter,...

    longhorn, where did you get that analog meter, and what exactly is it called? id like to get my hands on one just like that one.
  5. that's all there is to making a captret out of an...

    that's all there is to making a captret out of an electrolytic cap?? just rip the cap off of the end without the leads? did you fill it with distilled water or something? I've been mixing it up...
  6. sounds kind of like the SSG Lasersaber/Minoly...

    sounds kind of like the SSG Lasersaber/Minoly Radiant Charger w/ Base Capacitor and diode mod.....

    Also, where do you have the filament bulb positioned? is it between the start of the trigger coil...
  7. Replies
    11
    Views
    5,412

    Faraday88 - are you saying that a setup with the...

    Faraday88 - are you saying that a setup with the bipolar sequential switching is best for rejuvenating batteries?
  8. Replies
    11
    Views
    6,179

    I just read all the comments and am going to go...

    I just read all the comments and am going to go back and start watching the vids, but I want to ask, what exactly is the goal for this motor? Is it basically an energizer with amplified torque and...
  9. Replies
    20
    Views
    9,370

    Ralph, it's definitely good that you are going to...

    Ralph, it's definitely good that you are going to build an SG, but for your first time doing so, you shouldn't change anything at all about the circuitry and magnet setup. keep them all N facing...
  10. bigmotherwhale - you should download 'express...

    bigmotherwhale - you should download 'express sch' and 'express pcb' so you can doodle up your schematics, instead of having to do the pita method u are using now. :)

    I'm actually running a HDD...
  11. Replies
    39
    Views
    20,744

    Tom C, Is Amenhotep the name that you are...

    Tom C, Is Amenhotep the name that you are looking for??

    Everyone, you must use materials that are in their 100% natural form. If it can be found in that specific form naturally on Earth,...
  12. Replies
    5
    Views
    3,081

    Interesting.... I've noticed that, after...

    Interesting.... I've noticed that, after 'killing' my regular lead acid batteries by running them down to the point where my SG stops running.... then putting them on the regular DC charger under 2A...
  13. So it is 12:32PM here on the East Coast, and I...

    So it is 12:32PM here on the East Coast, and I have some interesting results to post for my little setup as described above. I am using a 650CCA battery on 'Run' and an 800CCA battery on charge. ...
  14. I've been wanting to drive some ground rods into...

    I've been wanting to drive some ground rods into the ground anyway, so I went ahead and replicated, but with a 2 foot piece of 1/2" rebar and 1/2" piece of old copper pipe and 12awg double-insulated...
  15. yes it worked!!! thank you!!

    yes it worked!!! thank you!!
  16. heh... well now I know exactly what to look for...

    heh... well now I know exactly what to look for to change!!! haha
  17. It's the link in the third post of this thread....

    It's the link in the third post of this thread. The one 'Branch Gordon' posted. It's apparently an Excel calculator that you made to calculate the approx. COP of the SG. I tried changing the '37;'...
  18. sorry, I didn't mean to over-elaborate and make...

    sorry, I didn't mean to over-elaborate and make it sound like I had more than a simple question for you... what I would like to know is this: are the ring magnets off of speakers OK to use for a...
  19. Completely understandable. It's always best to...

    Completely understandable. It's always best to keep it simple (keep it simple, stoopid! haha) to start with, and replicate original designs so you at least have a 'control' for further...
  20. understandable, and thank you for the heads up. ...

    understandable, and thank you for the heads up. Just about all of my schematics come from the reputable sources who are involved in this forum and the energetic forum, for example, Lasersaber,...
  21. also, I have a question regarding that Excel COP...

    also, I have a question regarding that Excel COP calculator.... it says that it's no longer available.... does someone have a new link to it or can someone send it to me? thanks!
  22. HAHAHA ohhhhh ohhhh wow Bung-ee..... It would...

    HAHAHA ohhhhh ohhhh wow Bung-ee..... It would seem that I'm much farther along in the learning process than you are and I've been going at this for half the time. As a matter of fact, I've been...
Results 1 to 22 of 25