Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Search:

Type: Posts; User: 888spo

Search: Search took 0.00 seconds.

  1. Thread: Forum back up!

    by 888spo
    Replies
    25
    Views
    8,613

    Back online and all looks good. Tks, D./

    Back online and all looks good.

    Tks, D./
  2. Replies
    38
    Views
    26,291

    Sticky: TST3 1st few runs

    Here are some results charging 24V Bank of 6V Batteries accross TST3 24V 20Amp with one panel delivering approx 9amps in full sunlight.

    The batteries are:

    4-5Yrs. old, sitting in a shed for the...
  3. Replies
    21
    Views
    8,309

    Flux, Sure, attached is the pdf. and the dxf...

    Flux,

    Sure, attached is the pdf. and the dxf output. Note i am using 3/4" material, trying to keep the cost in check. 2" material is double the cost.

    I haven't had much time to continue with...
  4. Replies
    21
    Views
    8,309

    John, I suspected those additional spacers...

    John,

    I suspected those additional spacers were overkill, tks. for advice, wondering if it had anything to do do with the high RPM range Rick was contemplating running the 10 Coiler at... are you...
  5. Replies
    21
    Views
    8,309

    Hi Monty, Send me a PM and i'll forward you...

    Hi Monty,

    Send me a PM and i'll forward you the .dxf so that you can have it made locally. They'll generate the g-code from the file and get exactly what i have. I haven't completed the other...
  6. Replies
    21
    Views
    8,309

    122712281229 Hi Ralph, How is progress on...

    122712281229

    Hi Ralph,

    How is progress on your 10 Coiler?

    I have finally completed my plexi rotor, decided to go in a little different direction. wanted go with full 2"... but WOW when i saw...
  7. Replies
    9
    Views
    4,558

    Aaron, I purchased the unit via Renaissance...

    Aaron,

    I purchased the unit via Renaissance Charge, would you know if they are in operation and remain licensed to service these units?

    Tks. D./
  8. Replies
    9
    Views
    4,558

    Solar Tracker Fan Stopped

    Hi,

    I have been using a ST 20amp for over 6 months hooked up to one 24V panel without any issues. comes on right before daybreak and keeps on charging right till dusk. A few days ago the fan just...
  9. Replies
    20
    Views
    7,590

    Les, nice setup! what diameter rotor did you go...

    Les, nice setup! what diameter rotor did you go with? I can't tell on the video, but is the rotor width equal to magnet size? copper pipe std. 1/4" tubing?

    Tks. D.
  10. Replies
    27
    Views
    9,586

    Nice board Tom, and notable improvements over the...

    Nice board Tom, and notable improvements over the earlier boards. will it be available soon?

    D./
  11. Thread: 3PM Kit Magnets

    by 888spo
    Replies
    96
    Views
    29,680

    John, thank-you for keeping this open to...

    John, thank-you for keeping this open to everyone. Looking forward to the experience.

    D./
  12. Thread: Introduction

    by 888spo
    Replies
    31
    Views
    15,418

    Hi Karl, Prius muscle car, who would have...

    Hi Karl,

    Prius muscle car, who would have thought ;) Sounds like your getting more low end torque? I didn't attend the conference but am curious about any sensor mods the groove needs to work...
  13. Tks for posting archive John; i have not read...

    Tks for posting archive John; i have not read this collection in its entirety... probably bits and pieces from different sites on the net. Appreciate you pulling this together.

    D./
  14. Replies
    5
    Views
    2,479

    Tom, Came across a few videos on u-tube...

    Tom,

    Came across a few videos on u-tube "magnetite cores" one fellow is using epoxy successfully. He does emphasize keeping the mixture as dense as possible, makes sense if you want to pack as...
  15. Thread: Introduction

    by 888spo
    Replies
    31
    Views
    15,418

    Hi Dane, Sounds similar to the EFIE device...

    Hi Dane,

    Sounds similar to the EFIE device that George Wiseman sells, I bought two a few yrs. soldered it them up and hooked it up to my O2 sensors the HHO cell i built was pretty crude it ...
  16. Thread: Introduction

    by 888spo
    Replies
    31
    Views
    15,418

    Hi Gary, did you gain any mid-range by adding the...

    Hi Gary, did you gain any mid-range by adding the baffles, I'm kinda impartial to the popping, those one-off pops that sound more like un-synchronized back-fire i can live without, but dropping it...
  17. Replies
    5
    Views
    2,253

    Hi Matt, I agree get the new batts... I also...

    Hi Matt,

    I agree get the new batts... I also wasted countless hrs. if not days trying to get some life out of an otherwise a bad set of batteries. Frustrating effort, especially when getting...
  18. Thread: Introduction

    by 888spo
    Replies
    31
    Views
    15,418

    Hi Gary, Nice Ride! She must sound wonderful;...

    Hi Gary, Nice Ride!

    She must sound wonderful; any sweet popping on downshifts;) looks like you had quite a bit of tigging to do on the exhaust build...? Oops sorry missed introductions. My name is...
  19. Replies
    5
    Views
    2,479

    Core Material - Magnetite

    Hi all!

    Anyone out there fiddle around with casting their own cores? Looking for some pointers on the process... Picked up some Fe304 locally and checking around on what is the preferred mix;...
Results 1 to 19 of 19