Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE
2020 ENERGY CONFERENCE

Monero XMR

Search:

Type: Posts; User: Yaro1776

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    2,459

    Slick design work! The location and coil locking...

    Slick design work! The location and coil locking feature is very good. The modular assembly allows stacking of several assemblies as you have shown.
  2. Replies
    36
    Views
    7,368

    Dave, Thanks for the lead on the Uber...

    Dave,

    Thanks for the lead on the Uber strapping tape. Checked out the url and it appears worthy of a trial. As the rotors increase in diameter and the Neo's become bigger every little bit of extra...
  3. Replies
    36
    Views
    7,368

    6 Pole First Spin

    Another day in the continuing adventure of the 6 Pole ZFM started with mounting two opposing N-S Neo's on the rotor. Rotor was then installed to check the overall pole displacement for each coil. The...
  4. Replies
    36
    Views
    7,368

    Thanks for the concern Dennis and Aaron. The...

    Thanks for the concern Dennis and Aaron.

    The dry Neo assembly was done to check the fits and forces involved on the rotor prior to applying the adhesive. The rotor was not in the motor and this...
  5. Replies
    36
    Views
    7,368

    6 Pole Phase 2

    The machine shop came through with the motor parts today. The parts completed were the Timing rotor and the 6 Pole Neo rotor. Tried a dry assembly of the Neo magnet components along with a steel rod...
  6. Replies
    17
    Views
    2,459

    Joe - the Oscope wave should a form of square...

    Joe - the Oscope wave should a form of square like wave, but with a 24 volt input to the two coil leads it should show +/- 24v on the scope. One scope lead to one coil wire and the lead's ground to...
  7. Replies
    17
    Views
    2,459

    Joe, Welcome to the very exclusive (at this...

    Joe,

    Welcome to the very exclusive (at this point) and very limited ZFM club that have experienced a rotor failure at high speed. Needless to say, glad all is well.

    Most experimenters do not...
  8. Replies
    17
    Views
    2,459

    Latest vid demonstrates that you have overcome...

    Latest vid demonstrates that you have overcome the initial setup problems. The reed switch support and positioning assembly is well done - this certainly will help with the timing. Assume that you...
  9. Hey RS, Great and detailed effort in showing...

    Hey RS,

    Great and detailed effort in showing the inner workings of the Bedini FW. The experiment depicting the magnets' field is excellent using the Hall sensors in combination with the Oscope....
  10. Replies
    36
    Views
    7,368

    6 Pole Virtual 60 Degree Poles

    Hello to all,

    Prolonged tweaking and calibration of the the 6 pole ZFM motor has resulted in the virtual pole positions to be all very close to the desired 60 degree arc angle. So all the...
  11. Replies
    36
    Views
    7,368

    Hey RS, The 3 coil arrangement is a straight...

    Hey RS,

    The 3 coil arrangement is a straight progression from the 2 coil ZFM and the rotor is a 6 pole Neo arrangement. Coils have been made without a trigger wire and they are a 45 degree arc...
  12. Replies
    36
    Views
    7,368

    Joster, The three coil design was a brain...

    Joster,

    The three coil design was a brain cramp on my part as a logical progression of the original 2 coil ZFM. I did not realize that the different Neo config would create the coil pole...
  13. Replies
    36
    Views
    7,368

    6 Pole Motor Assembled

    Finally completed the coil winding segment of this project and assembled the 6 rotor pole YZFM. Cheating a bit here by using a 4 pole unit with 2 Neo's - pics are below.

    The next step is to...
  14. Replies
    17
    Views
    2,459

    Checked out the YT link this morning, your ZFM...

    Checked out the YT link this morning, your ZFM Motor runs very smoothly and is very quiet. Great build!!!

    Love the pillow block design and construction using the 3D printer.
  15. Replies
    17
    Views
    2,459

    Joe, The recovery circuit is just an add on...

    Joe,

    The recovery circuit is just an add on and not necessary for operation of the ZFM circuit. The overheating of the transistors can be caused by several things, one primary reason is that the...
  16. Replies
    17
    Views
    2,459

    I like your attitude!!! :clap:

    I like your attitude!!!
    :clap:
  17. Replies
    36
    Views
    7,368

    60 degree Arc of Virtual Coil Poles

    In the latest set of experiments the 45 degree coil in the standard ZFM and rotor exhibited a 70 degree virtual coil pole arc with the coil radial distance increased by 0.24" over the prior...
  18. Replies
    36
    Views
    7,368

    Greetings to all the wanderers of the aether,...

    Greetings to all the wanderers of the aether,
    Having concluded the first phase of the next generation ZFM, one can now go forward to the actual design phase of this project. Please bear in mind that...
  19. Replies
    36
    Views
    7,368

    6 Pole Coil Arc

    Over the weekend a 45 degree coil (210 ft #20 mag wire) was wrapped and installed in the existing YZFM motor body using the same rotor and Neo config as the prior N-S test. Same degree wheel, 12v...
  20. Replies
    36
    Views
    7,368

    Design Phase Next Gen ZFM

    Spinning my wheels here with this post - moving to a .PDF file to keep the information flowing. Apologize for the inconvenience.
    7442
  21. Replies
    36
    Views
    7,368

    Greetings to all the wanderers of the aether,...

    Greetings to all the wanderers of the aether,
    Having concluded the first phase of the next generation ZFM, one can now go forward to the actual design phase of this project. Please bear in mind that...
  22. Replies
    36
    Views
    7,368

    Just tried a three paragraph copy and paste from...

    Just tried a three paragraph copy and paste from the Word document I have been using to Quick Reply. Clicking the Post Reply button gives a "do you want to leave page" message. Pushing yes button...
  23. Replies
    36
    Views
    7,368

    Aaron, Tried another computer with Win7Pro...

    Aaron,

    Tried another computer with Win7Pro with the same negative results. Frustrating, but then again I can post sometime in the future. I will continue my experiments irregardless of these speed...
  24. Replies
    36
    Views
    7,368

    Hey Aaron, Still having issues in not being...

    Hey Aaron,

    Still having issues in not being able to post over a 100 words or so when in advanced mode. Preview of post yields a blank screen and then wind up not being able to to bring up EFS site...
  25. Replies
    36
    Views
    7,368

    Functionality Test

    Functionality Test
Results 1 to 25 of 356
Page 1 of 15 1 2 3 4