Search:

Hi Gary,
I will try something following your suggestions, but I do not have an o-scope yet...
Will update
Thx again for the support
Claudio

xx
Hi Gary,
thank you for waisting time for me...:notworthy:
I put a new regulator, but this one exploded after about 10 secs !!
I think the connections are ok..
Maybe there is a mistake in the...

Hi Gary,

I connected everything and started the SSG, the green Led was pulsing but in about 5 seconds the 7812ABV chip burned !
Should I replace it with a different chip or something is wrong...

Hi Gary,

I am a good student!
Hahahaha
Will let you know the results !

Hi Gary,
thank you for the instructions.
One more question. There is no connection to the charge battery positive?
"
#3 on the cap discharge board is connected to #7 on the SSG board and also to...

Thank you for your advice Gary but it doesn't work ... maybe there is problem with the circuit ?
When I connect the charge battery it heats up and I see spikes ...
I should check if I made some...

Hi Aaron,
looking for similar steel balls in Italy, very very difficult to find shotgun steel balls.But there are manufacturers of steel balls for bearings. There are different quality of balls,...

Hallo,

I am not an expert on electronics ( I am learning) but I managed anyway to build my Bedini SSG, it is running perfectly rejuvenating batteries without problems.

Bike wheel diam. 63,5 cm ...

Hi everybody,
I found this chart about welding rods categories..
Looks like R60 in Europe is the G2, R60-G is G3 and R45 is G1..
In Europe you can find them easily on eBay

Check it out

7263

Dear Faraday88, RS_, Richard,

I am finally back to my project, I hope you will be still available to help me…

My SG :
Bike wheel diam. 63,5 cm
21 Magnets 5x2,5x1cm (smaller than indicated on...

done..
I will test on breadboard and if it works will send to manufacture, conductivity is way better on manufactured PCB

thank you

6934

:wall: :wall::wall:

thx

6933

Thank you for your specifications, very instructive for me:o
Breadboarding will prove if it will work :thinking:
The 7812 I got is the L7812ABV-DG from mouser
Modified the PCB following your wise...

:wall:

6931

Hallo RS_ and Richard,

thank you again :prof: , I am learning.. :o

I'm referring from this schematic coming from the JB and PL Books..
6928

H11D1 will be installed, I just didn't find the...

Thank you Richard,

is this the idea ?

6927

I'm a little confused here... :thinking:
One or two LEDs ?
Am I getting this correctly ?

6926

will do !
between the 555 output and R12 (10k) ? what kind of resistor ?

this circuit is more and more similar to the JB "original"...:)


6921

page 46-48 shows the discharge circuit parts and specs very precisely, my PCB is based on that...

PCB ready for etching...
6920

done

6918

This comes directly from the JB Intermediate Book (pages 46-48) "Discharge circuit", JB and Mr. Lindemann keep reminding to stick on what JB is suggesting for this to work, for the resistors the book...

Thanks Richard,

Richard, RS_ , should I use 1/4W resistors or 1/2W - 1W work anyway ?
I think I will send the PCB to production, it's not so expensive and conductivity is much much better...
...

OK thx,
should I get 1/4 W resistors (all of them) or is it ok with 1/2W or 1W ?
added copper on pads 5 and 6... too much ?
anything else to improve ?
here the definitive PCB(?)

almost done...

I'm sorry I don't get it, how should the pots be connected ?
Please use the yellow letters/numbers

6906

Now I have 1A, 2B, 5C, 6D. Is that the correct one ?
Just to be sure...

6904

PCB updated ...
will re-check connections and holes
will try the circuit on bread board first...
pots section ok...