Search:

Hi daucupace, :)

In studying your photos it looks like you may have some bad solder joints, especially on the base resistors. Use a good heat sink on each component and reheat all your solder...

Hi Jules, :)



Just finishing up a small two stage mechanical oscillator build that my grandson and I started in April of this year. He took a real job, with pay, during the summer so I...

Hi Julian, :)

Thanks for posting your results. I admire the professionalism and dedication you bring to your experiments! Good work. :clap:

I noticed in the video that Skinner's device used...

Hi Yaro, :)

I would also be interested in seeing how a four magnet rotor would behave in this test. Both with all north out and then with alternating N,S,N,S out.

It would also be interesting...

The two stage oscillator build nearly came to a halt when my grandson took a summer job in construction. And now his school has started again, and he has too heavy of a scholastic load to continue...

Hi Yaro, :)

These are interesting experiments, but I have a couple of questions about them. .............First, what is the "repulsive dead zone"? :confused: And second, if you installed a steel...

Hi Joster, :)

Try this link. http://www.cheniere.org/sales/online-store.htm

Hi Bro D, :)



I'm not Aaron, but the answer to your question is no.

What Peter demonstrated was a conventional radiant charge going into the charge battery in parallel with a large battery...

Hi Nuvisys, :)



How does this equate with the following quotes?

I've never had very good luck with NiCads in anything. And I also haven't had any success trying to rejuvenate them either. The NiMH's on the other hand have worked very well for me in most...

Hi Bob, :)



I haven't tried any nickel iron batteries, but I have replaced nearly all the small alkaline dry cells in most of the devices in our house with NiMH ones that I recharge with my 1AU...

I experimented with an attraction motor powering a G-field (flux gate) alternator that showed some very interesting properties. I want to build a better one from scratch and power it with a split the...

Hi Bob, :)



Been wondering what happened to you. :confused: Welcome back!! :D

Hi Nuvists, :)




It can be used with any fuel that is spark ignited in the engine such as gasoline, alcohol, L.P., nitro-methane, ammonia, etc. Walt Jenkins can even burn water with plasma...

Hi Faraday88, :)



That's what the pause button is for. LOL :surprise:

Hi Jeremiah, :)





If the high voltage is shorting through the insulation you should be able to see sparks and arcing, especially after dark. It will also probably misfire if this occurs.

Hi Jeremiah, :)



Yes these plugs do run on the very cold side, but that's not really a problem for me. The only time one fouled out was in my Bradley GT with modified air cooled VW engine...

Hi energialibre, :)



You apparently have the capability to translate into English as demonstrated in this quote. For those of us in the USA who are not multilingual, it would be helpful if you...

Hi Alstrup, :)

I'm also using surface discharge (NGK BUE) plugs in my Bradley GT kit car that has a modified, air cooled VW engine. Can't speak to their longevity yet, but they give really good...

Here's another update. We're getting closer, but still not there yet.


https://www.youtube.com/watch?v=1sKSQFHioGI

Hi Jeremiah, :)



The taylor spiro-pro wire is 350 ohms/foot. It has a magnetically permeable core with a thin steel wire tightly wound around the core.

I posted the link to that old post so...

Hi Jeremiah, :)



I wouldn't do that. The MSD 5520 street fire works fine with the MSD 8222 blaster coil in my single cylinder generator application. However, the Granatelli solid wire may be...

Yes! Everything in nature is in perpetual motion. This is all explained in this book. Have you ever wondered what would happen if all the electrons suddenly stopped spinning around the nucleus of...

Hi Jeremiah, :)

Just curious, is this a modified K321? Pulling tractor? Cub Cadet?

Besides the ignition, what other mods have you done to the engine? Is the Pertronix Ignitor 1 made...

Hi Jeremiah, :)

Are we still talking about your 14HP Kohler engine, or are you now talking about this on your car instead? :confused: