Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 2 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Tab Content
  • Deuis's Avatar
    Yesterday, 05:02 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Faraday your quite welcome to blow sh it up in your own time. Caps... as in plural. The word Cap Bank was probably a giveaway too. Of course I have...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-21-2018, 01:16 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Hi Faraday, The caps top out at 900V @ 2200uF. While I would love to see how high this charge goes I like to keep the smoke inside the...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-20-2018, 05:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    If i'm understanding you correctly yes. But then again im an electrician who doesnt understand electricity so take that with a grain of salt :)
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-20-2018, 05:17 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The wheel specs are 18 x 2x1x1/2 double stacked north out. It's not the trigger potentiometer or coil where the heat has manifested. I have put a...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-20-2018, 03:03 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The SG doesnt run without power assist as yet. I haven't loosened the bearings or fixed the aerodynamics and the wheel weighs about 5kg. There are...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-19-2018, 02:32 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Me too, I swapped the 200ohm out for a 600ohm and same thing. Voltage went up by about 40% and sat on about 80 degrees. I hooked a 15W x 240V...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-16-2018, 09:46 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Interesting experiment as above. Typically the 12.7V power source could only ever supply .811W to a 199 ohm resistor. After triggering, the stable...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-16-2018, 08:32 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Some Data on the standard SG with variable air gap. I started at the closest setting of 3mm then walked it out 1mm at a time until the lowest speed...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-15-2018, 08:37 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Please dont clog up this post. This is a standard SG setup with an assisted motor. 8 filar coil, 1 trigger, 7 Power. You can see the...
    73 replies | 5463 view(s)
  • Deuis's Avatar
    06-15-2018, 07:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    I have now hooked up the SG circuit to the 8 filar 18ga coil. Under power assist I can dial down to a speed where the transistors are only just...
    73 replies | 5463 view(s)
No More Results

1 Visitor Messages

  1. View Conversation
    Hi Yaro --

    What State are you in now. I just read your latest post and you said both boards are burned up now??? How could this happen.

    -- Jim
Showing Visitor Messages 1 to 1 of 1
About Yaro1776

Basic Information

About Yaro1776
Location:
Heart of Vermont
Occupation:
Snowman

Signature


Yaro

"The Universe is under no obligation to make sense to you." -Neil Degrasse Tyson

Statistics


Total Posts
Total Posts
263
Posts Per Day
0.12
Visitor Messages
Total Messages
1
Most Recent Message
02-26-2014 10:49 PM
General Information
Last Activity
Yesterday 11:49 AM
Join Date
08-07-2012

2 Friends

  1. Deuis Deuis is offline

    Senior Member

    Deuis
  2. James McDonald James McDonald is offline

    Senior Member

    • Send a message via AIM to James McDonald
    James McDonald
Showing Friends 1 to 2 of 2