Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 2 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Tab Content
  • Deuis's Avatar
    Today, 01:16 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Hi Faraday, The caps top out at 900V @ 2200uF. While I would love to see how high this charge goes I like to keep the smoke inside the...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    Yesterday, 05:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    If i'm understanding you correctly yes. But then again im an electrician who doesnt understand electricity so take that with a grain of salt :)
    71 replies | 5254 view(s)
  • Deuis's Avatar
    Yesterday, 05:17 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The wheel specs are 18 x 2x1x1/2 double stacked north out. It's not the trigger potentiometer or coil where the heat has manifested. I have put a...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    Yesterday, 03:03 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The SG doesnt run without power assist as yet. I haven't loosened the bearings or fixed the aerodynamics and the wheel weighs about 5kg. There are...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-19-2018, 02:32 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Me too, I swapped the 200ohm out for a 600ohm and same thing. Voltage went up by about 40% and sat on about 80 degrees. I hooked a 15W x 240V...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-16-2018, 09:46 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Interesting experiment as above. Typically the 12.7V power source could only ever supply .811W to a 199 ohm resistor. After triggering, the stable...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-16-2018, 08:32 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Some Data on the standard SG with variable air gap. I started at the closest setting of 3mm then walked it out 1mm at a time until the lowest speed...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-15-2018, 08:37 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Please dont clog up this post. This is a standard SG setup with an assisted motor. 8 filar coil, 1 trigger, 7 Power. You can see the...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-15-2018, 07:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    I have now hooked up the SG circuit to the 8 filar 18ga coil. Under power assist I can dial down to a speed where the transistors are only just...
    71 replies | 5254 view(s)
No More Results

1 Visitor Messages

  1. View Conversation
    Hi Yaro --

    What State are you in now. I just read your latest post and you said both boards are burned up now??? How could this happen.

    -- Jim
Showing Visitor Messages 1 to 1 of 1
About Yaro1776

Basic Information

About Yaro1776
Location:
Heart of Vermont
Occupation:
Snowman

Signature


Yaro

"The Universe is under no obligation to make sense to you." -Neil Degrasse Tyson

Statistics


Total Posts
Total Posts
263
Posts Per Day
0.12
Visitor Messages
Total Messages
1
Most Recent Message
02-26-2014 10:49 PM
General Information
Last Activity
Yesterday 03:57 AM
Join Date
08-07-2012

2 Friends

  1. Deuis Deuis is offline

    Senior Member

    Deuis
  2. James McDonald James McDonald is offline

    Senior Member

    • Send a message via AIM to James McDonald
    James McDonald
Showing Friends 1 to 2 of 2