Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 2 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Tab Content
  • brodonh's Avatar
    Today, 06:00 AM
    Hi All, New vid of 200 pounder Newman motor smoke test. USE DROP BOX LINK IN PREVIOUS POST #41 Talked to Geoff Miller and he was very glad...
    42 replies | 9926 view(s)
  • Deuis's Avatar
    Today, 01:16 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Hi Faraday, The caps top out at 900V @ 2200uF. While I would love to see how high this charge goes I like to keep the smoke inside the...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    Yesterday, 05:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    If i'm understanding you correctly yes. But then again im an electrician who doesnt understand electricity so take that with a grain of salt :)
    71 replies | 5254 view(s)
  • Deuis's Avatar
    Yesterday, 05:17 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The wheel specs are 18 x 2x1x1/2 double stacked north out. It's not the trigger potentiometer or coil where the heat has manifested. I have put a...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    Yesterday, 03:03 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The SG doesnt run without power assist as yet. I haven't loosened the bearings or fixed the aerodynamics and the wheel weighs about 5kg. There are...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-19-2018, 02:32 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Me too, I swapped the 200ohm out for a 600ohm and same thing. Voltage went up by about 40% and sat on about 80 degrees. I hooked a 15W x 240V...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-16-2018, 09:46 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Interesting experiment as above. Typically the 12.7V power source could only ever supply .811W to a 199 ohm resistor. After triggering, the stable...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-16-2018, 08:32 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Some Data on the standard SG with variable air gap. I started at the closest setting of 3mm then walked it out 1mm at a time until the lowest speed...
    71 replies | 5254 view(s)
  • DMANN's Avatar
    06-16-2018, 09:01 AM
    I posted a outrunner stator mold to Thingiverse if anyone may be interested. It uses the Babcock process with #8 steel shot. It can be used in a...
    24 replies | 3824 view(s)
  • Deuis's Avatar
    06-15-2018, 08:37 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Please dont clog up this post. This is a standard SG setup with an assisted motor. 8 filar coil, 1 trigger, 7 Power. You can see the...
    71 replies | 5254 view(s)
  • Deuis's Avatar
    06-15-2018, 07:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    I have now hooked up the SG circuit to the 8 filar 18ga coil. Under power assist I can dial down to a speed where the transistors are only just...
    71 replies | 5254 view(s)
No More Results
About Deuis

Basic Information

About Deuis
Location:
Australia
Interests:
Isnt it obvious?
Occupation:
Technician

Signature


Cant spend it when your dead.

Statistics


Total Posts
Total Posts
143
Posts Per Day
0.25
General Information
Last Activity
Today 01:53 AM
Join Date
11-21-2016

6 Friends

  1. BobZilla BobZilla is offline

    Senior Member

    BobZilla
  2. brodonh brodonh is online now

    Senior Member

    brodonh
  3. Dave Wing Dave Wing is offline

    Senior Member

    Dave Wing
  4. DMANN DMANN is offline

    Senior Member

    DMANN
  5. Gary Hammond Gary Hammond is online now

    Senior Member

    Gary Hammond
  6. Yaro1776 Yaro1776 is offline

    Senior Member

    Yaro1776
Showing Friends 1 to 6 of 6