Deuis
Senior Member

Hi Rokan, :) Did you try the suggestions I listed in post 992 with additional capacitors and a Faraday shield to see if RFI is the problem?

Hi Aaron, :) I tried testing mine with a multi-meter and it showed infinite resistance in both directions whether in normal resistance mode or...

Thanks for the interest John, I definitely was pushing the envelope with that particular test at maximum advance and 36v in parallel coil...

Hello to All, The prior post Parallel experiments, with the 2.0Lx0.5Tx0.5W Neo, were interrupted by a skin failure of the Neo magnet at around...

The magnets are glued inside the holders and are not interchangable. Is there any merit you can see in repulsion mode?

Some more data. 26" wheel 12V back and front. 18 scalar magnets. 9 coils X 8 filar X 18ga. 6mm air gap. Primary drawdown 12.12V @ 30mins

Some more data. 26" wheel 12V back and front. 18 scalar magnets. 9 coils X 8 filar X 18ga. 6mm air gap. Rotor was 310rpm with 1ohm trigger....

Hi Aaron, I wasn't going in that direction as others including John Bedini have proven its more efficient in attraction. It takes a lot of...

Hi Yaro, I've ordered another 26" wheel last week so I can run Scalar North and North out motors anytime I wish for direct comparisons. Scalar...

Looking at it after I posted... it cloud be 350KHZ not 350MHZ. Dave Wing

Questions: In figure 8 of John’s drawing he shows a hand drawn scope shot of the spikes with their peaks showing a wave apparently at 350MHZ. I...

I thought I would repost this diagram that was found in a video made by Davy Oneness, it is a pictorial tribute to John’s work that is combined...

Hello JD, Quick note to you that it would be useful to explain the "scalar north" magnet arrangement for those who have not referenced the prior...

Hello Jules, Glad to see that your progress is very positive. It rotates at good speed! It appears that the generator is running around 1000 RPM...

Hi Jules, :) What you have shown in the attachments is the "drive battery is disconnected from the HV" and the HV line connected directly to a...

Hi Micheal and Cmor, :) REGAUGING is one of those mystical terms that people use without really knowing what it means. I'm not sure I know...

Hi Cmor, :) No, there is no way to do that. That's not how they are made. The wire and/or mosfet leg just slips inside a sleeve. Then a...

Hi Jules, :) Here's a video of a window motor John Bedini built several years ago that runs from only a capacitor that keeps itself recharged....

Hi Jules, :) Sorry! :wall: Look at that a little closer. The new diode you added is connected directly across the coil in parallel, in a...

Hi Jules, :) Theoretically I think that should work. The main problem I see is getting the FETs and/or BJT to switch at exactly the same time....

Hi Jules, :) Here's a method of "back popping" the run battery that Aaron originally posted.

Hi Jules, :) This still doesn't provide any path from the battery negative post back to the top of the coils when the FETs switch off. The...

Hi Jules, :) Picking up with where we left off in the other thread. This will work fine for charging a second battery but not for the run...

Hi Jules, :) Don't do that! The diodes are correct. If you reverse them, it will cause a direct short through them and the FET directly back...

Hi Jules, :) No. We use "conventional current" for our schematic symbols as well. (I usually think in terms of "electron current" because...

Hello Jules, Very good to see your machine in operation, sweet! Congratulations to you on your persistence and focus. Now the real adventure...

Hi Jules, :) Nice work. :clap:

Hi Cmor, :) Maybe you'd better go with six FETs. (72000/12000 = 6) Sorry about my miscounting. My bad. I didn't look at the picture again...

Hey JD, We all be asleep at the wheel! Great results from the 9 Coiler test demonstrating that it is possible to build a modified SSG that can...

Hi Cmor, :) The idea is to divide the discharge current up as evenly as possible (hence matched) and stay well within the current and voltage...