Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 2 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

Tab Content
  • Deuis's Avatar
    07-18-2018, 02:32 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    https://www.sciencedirect.com/science/article/pii/S0304885318311090
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-14-2018, 11:07 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Yes its an 8 Strand coil with pairs of strands in parallel. These pairs are in series. Early days yet, but yes thats the plan. Heres a chart...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-14-2018, 02:50 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Schematic was wrong. Its dual coils in series.
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-13-2018, 04:26 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Shoo fly, don't bother me.
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-13-2018, 01:08 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Thanks RS, This 23AWG Generator coil is a mutilstranded twisted coil in the below configuration. All testing was done with this coil in different...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-11-2018, 11:09 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    - My magnets are set for the moment, double stacked 2X1X1/2". Spacing is set to 18 magnets on a 26" wheel. - Core material i've played with a...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-11-2018, 12:27 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Here you go Patrick I cleaned up the data and used a better meter. Keep in mind that using a resistive load straight from the coil is not the way to...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-10-2018, 04:02 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Hi Patrick, This is not a bedini motor/energiser its a test rig, reading specific generator coil data. The wheel is 26" and weighs over 5kilos...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-08-2018, 03:39 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The wheel is PWM. I've got a meter with better resolution I can use later on. The output is highest at the highest speed, the experiment was to...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-08-2018, 01:38 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Focusing in on the 300RPM mark I have used varying resistances to simulate a load. While the resolution on the ammeter is not adequate, the results...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-07-2018, 09:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    I used the highest output Gennie coil and perfomed some speed data as attached. The differential is the wheel open circuit W + Gen coil output W -...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    07-05-2018, 03:39 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Some data against some identical generator coils in different formations. Each coil is 8 filar, 23awg. Series, parallel and a combination. The...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    06-27-2018, 12:06 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    I do remember a windmill type, was it in the vacuum series? I've lost all bedinis DVD's which is unfortunate. Im all for decent dialogue on ideas...
    104 replies | 7416 view(s)
  • DMANN's Avatar
    06-26-2018, 01:37 PM
    Drill jig for 8 in. cake pan added on 06/26/2018 at 4:27 PM est. Use a 1/4" drill bit for holes. Once all holes are drilled you can take a step up...
    26 replies | 4268 view(s)
  • DMANN's Avatar
    06-26-2018, 09:53 AM
    Sandwich style bearing hubs added along with wire protector boots to go on slots on 06/26/2018 at 12:43 PM est. Bearing size is 3/4" X 1 5/8" X...
    26 replies | 4268 view(s)
  • Deuis's Avatar
    06-24-2018, 05:02 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Faraday your quite welcome to blow sh it up in your own time. Caps... as in plural. The word Cap Bank was probably a giveaway too. Of course I have...
    104 replies | 7416 view(s)
  • Deuis's Avatar
    06-21-2018, 01:16 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Hi Faraday, The caps top out at 900V @ 2200uF. While I would love to see how high this charge goes I like to keep the smoke inside the...
    104 replies | 7416 view(s)
No More Results
About DMANN

Basic Information

Age
41
About DMANN
Biography:
North Carolina native
Location:
Farmville
Interests:
God, family, guns, free energy systems
Occupation:
public safety

Statistics


Total Posts
Total Posts
172
Posts Per Day
0.09
General Information
Last Activity
06-26-2018 07:26 PM
Join Date
06-04-2013

1 Friend

  1. Deuis Deuis is offline

    Senior Member

    Deuis
Showing Friends 1 to 1 of 1