Bedini RPX Sideband Generator

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


ONLY 150 118 90 2 SEATS AVAILABLE! - 2018 ENERGY CONFERENCE

Monero XMR

  • Deuis's Avatar
    Today, 03:03 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    The SG doesnt run without power assist as yet. I haven't loosened the bearings or fixed the aerodynamics and the wheel weighs about 5kg. There are...
    61 replies | 5176 view(s)
  • Deuis's Avatar
    Yesterday, 02:32 AM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Me too, I swapped the 200ohm out for a 600ohm and same thing. Voltage went up by about 40% and sat on about 80 degrees. I hooked a 15W x 240V...
    61 replies | 5176 view(s)
  • Deuis's Avatar
    06-16-2018, 09:46 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Interesting experiment as above. Typically the 12.7V power source could only ever supply .811W to a 199 ohm resistor. After triggering, the stable...
    61 replies | 5176 view(s)
  • Deuis's Avatar
    06-16-2018, 08:32 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Some Data on the standard SG with variable air gap. I started at the closest setting of 3mm then walked it out 1mm at a time until the lowest speed...
    61 replies | 5176 view(s)
  • Deuis's Avatar
    06-15-2018, 08:37 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    Please dont clog up this post. This is a standard SG setup with an assisted motor. 8 filar coil, 1 trigger, 7 Power. You can see the...
    61 replies | 5176 view(s)
  • Deuis's Avatar
    06-15-2018, 07:54 PM
    Deuis replied to a thread Bedini 1984, 2017 style. in John Bedini
    I have now hooked up the SG circuit to the 8 filar 18ga coil. Under power assist I can dial down to a speed where the transistors are only just...
    61 replies | 5176 view(s)
No More Results

1 Visitor Messages

  1. View Conversation
    I have been wondering about a possible get together myself. I currently have a fairly flexible schedule and would be willing to meet you in macomb. You can PM me with appropriate times or my cell is 319-371-8352. Just dont expect much enlightenment from my end, but a chat to see where each other stand would be good.
Showing Visitor Messages 1 to 1 of 1
About Gary Hammond

Basic Information

Date of Birth
November 24, 1941 (76)
About Gary Hammond
Biography:
Christian, married, 2 sons, 4 grandkids, inventor (granted 1 patent), experimenter, mechanic, machinist, welder, entrepreneur
Location:
Macomb, IL
Interests:
cars, electronics, building prototypes
Occupation:
semi-retired

Signature


Gary Hammond,

Statistics


Total Posts
Total Posts
294
Posts Per Day
0.14
Visitor Messages
Total Messages
1
Most Recent Message
10-26-2012 01:10 PM
General Information
Last Activity
Today 03:13 PM
Join Date
07-30-2012

3 Friends

  1. ambady ambady is offline

    Junior Member

    ambady
  2. Deuis Deuis is online now

    Senior Member

    Deuis
  3. Kenowen Kenowen is offline

    Junior Member

    Kenowen
Showing Friends 1 to 3 of 3