Energy Science Forum - LENR

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX

2019 ESTC ALL SEATS SOLD OUT!
PRE-REGISTER FOR THE 2020 ENERGY CONFERENCE

Section Widget
Renewable Energy News

Electrical Science
Categories Widget (Show All)

Eric Dollard (1)

L.E.D. Technology (0)

LENR - Cold Fusion (0)

Solar (0)

Wind (0)
Recent Articles

LENR - Cold Fusion

There is no available content in category LENR - Cold Fusion

Recent Article Comments Widget
Recent Blog Posts
Recent Forum Posts

6 Pole Phase 2

The machine shop came through with the motor parts today. The parts completed were the Timing rotor and the 6 Pole Neo rotor. Tried a dry assembly of
Yaro1776 Today, 02:56 PM

Joe’s ZFM Adventures

Joe - the Oscope wave should a form of square like wave, but with a 24 volt input to the two coil leads it should show +/- 24v on the scope. One scope
Yaro1776 Today, 01:43 PM

Explorations of the Bedini Ferris Wheel Motor Energizer

RS I made some room.
Dave Wing Yesterday, 03:58 AM

Explorations of the Bedini Ferris Wheel Motor Energizer

Dave W, your PM box is full... plz deleat some PM's so i can send you a PM
RS_ 12-03-2019, 04:41 PM

Joe’s ZFM Adventures

Hi,

At the 2016 conference where JB demoed the ZFM, when i noticed that ZFM circuit did not have a Output Diode Bridge like a window motor
RS_ 12-03-2019, 02:32 PM

Explorations of the Bedini Ferris Wheel Motor Energizer

Joster,

The single NPN transistor SG type circuits are Energizers with Low Torque. The Bipolar circuits are High Torque circuits with energy
RS_ 12-03-2019, 02:17 PM

Explorations of the Bedini Ferris Wheel Motor Energizer

Hey RS,

Please forgive my ignorance but I need to ask a question. What is the difference in functionality between a single NPN transistor
Joster 12-03-2019, 07:54 AM

Explorations of the Bedini Ferris Wheel Motor Energizer

Aaron,
The waveform wheather it electrical or magnetic its all the same as you rightly expressed, either of the circuital parameters show the
Faraday88 12-02-2019, 09:39 PM

Explorations of the Bedini Ferris Wheel Motor Energizer

It is a modified B/C bipolar circuit. The Hub motor has 3 sets of bipolar transistors and the main wheel circuit has 5 sets of bipolar transistors....
RS_ 12-02-2019, 03:06 PM

Explorations of the Bedini Ferris Wheel Motor Energizer

nice! thats so cool! is it indeed a modified bedini cole? any chance of sharing the schematic?
Joster 12-02-2019, 02:59 PM

Explorations of the Bedini Ferris Wheel Motor Energizer

I've already reverse engineered the circuit, and have made PCB's of my version of the circuit
RS_ 12-02-2019, 02:36 PM

Help setting up Bedini SG properly.

Hi Gary,

Thank you for the reply. I rechecked and did reheat some solder joints but I think they were already soldered good in the first
daucupace 12-02-2019, 11:28 AM

Explorations of the Bedini Ferris Wheel Motor Energizer

following this closely....amazing stuff!!! What kind of circuit is this? i remember John saying "it's a highly modified Bedini Cole Switch"
Joster 12-02-2019, 06:10 AM

Explorations of the Bedini Ferris Wheel Motor Energizer

I had planed to take inductance and resistance measurements of the FW Hub Motor coil's this weekend to post along with these pic's...

My
RS_ 12-01-2019, 11:05 AM

Explorations of the Bedini Ferris Wheel Motor Energizer

Here are pics of the Ferris Wheel Hub Motor Timing wheel. When I received the FW, the 5, 1/2" magnets on the timing wheel were missing. You could
RS_ 12-01-2019, 10:44 AM

Gravity Power - 1939 style

That sounds fine. I will wait to see the new thread then start adding material. Yes Tseung just uses a different slant on the key ideas from Bedini et
JulesP 12-01-2019, 02:31 AM

Help setting up Bedini SG properly.

Hi daucupace,

In studying your photos it looks like you may have some bad solder joints, especially on the base resistors. Use a good
Gary Hammond 11-30-2019, 06:09 PM

Help setting up Bedini SG properly.

Hi Joster,

I get 1.4 - 1.5 ohm for each power winding and 3 ohm for the trigger...seems good to me..
daucupace 11-30-2019, 04:16 PM

Gravity Power - 1939 style

Another thread is no problem. I'll put it in the next Energy Times newsletter that might go out today if I can get it together fast enough.

Aaron Murakami 11-30-2019, 01:31 PM

Help setting up Bedini SG properly.

u could very well be right. what is the resistance of the coil you have? meaning if u put an ohm meter across one of the power windings what do u get?
Joster 11-30-2019, 05:12 AM

Bedini RPX Sideband Generator

Section Widget

Categories Widget (Show All)

Recent Articles

LENR - Cold Fusion

Recent Article Comments Widget

Recent Blog Posts

Recent Forum Posts