Activity Stream

RS I made some room.

Dave W, your PM box is full... plz deleat some PM's so i can send you a PM

Hi, At the 2016 conference where JB demoed the ZFM, when i noticed that ZFM circuit did not have a Output Diode Bridge like a window motor...

Joster, The single NPN transistor SG type circuits are Energizers with Low Torque. The Bipolar circuits are High Torque circuits with energy...

Hey RS, Please forgive my ignorance but I need to ask a question. What is the difference in functionality between a single NPN transistor switch...

Aaron, The waveform wheather it electrical or magnetic its all the same as you rightly expressed, either of the circuital parameters show the same...

It is a modified B/C bipolar circuit. The Hub motor has 3 sets of bipolar transistors and the main wheel circuit has 5 sets of bipolar...

nice! thats so cool! is it indeed a modified bedini cole? any chance of sharing the schematic?

I've already reverse engineered the circuit, and have made PCB's of my version of the circuit

Hi Gary, Thank you for the reply. I rechecked and did reheat some solder joints but I think they were already soldered good in the first...

following this closely....amazing stuff!!! What kind of circuit is this? i remember John saying "it's a highly modified Bedini Cole Switch" any...

I had planed to take inductance and resistance measurements of the FW Hub Motor coil's this weekend to post along with these pic's... My 20+ year...

Here are pics of the Ferris Wheel Hub Motor Timing wheel. When I received the FW, the 5, 1/2" magnets on the timing wheel were missing. You could...

That sounds fine. I will wait to see the new thread then start adding material. Yes Tseung just uses a different slant on the key ideas from Bedini...

Hi daucupace, :) In studying your photos it looks like you may have some bad solder joints, especially on the base resistors. Use a good heat sink...

Hi Joster, I get 1.4 - 1.5 ohm for each power winding and 3 ohm for the trigger...seems good to me..

Another thread is no problem. I'll put it in the next Energy Times newsletter that might go out today if I can get it together fast enough. I...

u could very well be right. what is the resistance of the coil you have? meaning if u put an ohm meter across one of the power windings what do u get?

Well that does sound interesting and yes, as with the Skinner based system, I would be very interested to hear of new developments. Would it be...

Sounds great. Preparing the next generation to think that such open systems are the norm :)

I've been corresponding with someone overseas for a while now that has something along those lines. I'll be posting something about it very soon and...

Hi Jules, :) Just finishing up a small two stage mechanical oscillator build that my grandson and I started in April of this year. He took a...

Hi Joster, Thanks for the quick reply. I removed the 10w and the 100ohm 2watt resistor and only the 4w potentiometer and the 100ohm 1 watt...

Just an idea not sure if it will work but it is what i would try next: I just realized you already have 100 ohms on the base of each transister so...

Hello everyone, I put the new 4watt potentiometer with the 100 ohm 2 watt resistor as shown in below picture, unfortunately it's still the same...

Hi Gary, My small scale device did not replicate all the features of Skinner's original system. You rightly point out some differences but I...

Thanks Yaro yes the ZFM seems to be a sparsely studied motor and yes i absolutely did under appreciate the forces occurring here. Anyhow, I fixed up...

Hi Julian, :) Thanks for posting your results. I admire the professionalism and dedication you bring to your experiments! Good work. :clap: I...

Hi Aaron, thanks for posting as I was just about to write a PM to you to ask for your opinion :) Yes please report on any results from a full sized...